Allied Telesis IE340 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 136

Allied Telesis IE340 Series Скачать руководство пользователя страница 33

Chapter 1: Overview

33

SFP Slots

The following IE340 switches have four slots for 100/1000Base-X fiber
optic, MSA-compliant SFP transceivers:



IE340-12GP



IE340-12GT



IE340-20GP

The IE340L-18GP switch has two SFP slots for Ethernet 1000Base-X fiber
optic, MSA-compliant SFP transceivers.

You can use transceivers to connect switches to other network devices
over large distances, build a high-speed backbone network between
network devices, or connect high-speed devices, such as servers, to your
network.

Refer to the product data sheet for a list of supported Ethernet
transceivers.

To protect SFP transceivers from heat-related damage, you should select
transceivers whose maximum operating temperatures exceed the
anticipated maximum ambient temperature at the switch installation site.
Table 3 provides recommendations for SFP maximum operating
temperatures for several ambient site temperatures.

Table 3. Maximum Installation Site Temperatures Versus SFP

Temperature Ratings

Maximum Ambient

Installation Site

Temperature

Recommended Maximum SFP

Operating Temperature

75 °C (167° F)

a

a.

The 75 °C ambient and 105 °C SFP operating temperatures are

not applicable to IE340L-18GP switch, which has a maximum

ambient temperature of 65 °C

.

105 °C (221° F)

65 °C (149° F)

95 °C (203° F)

55 °C (131° F)

85 °C (185° F)

≤

40 °C (

≤

104° F)

70 °C (158° F)

«
...
31
32
33
34
35
...
»

Содержание IE340 Series









































































































































Отзывы:

Нет отзывов