manualshive.com logo in svg

Allied Telesis IE340 Series, Руководство по установке, Страница: 25 / 136

Поделиться
Скачать
Allied Telesis IE340 Series Скачать руководство пользователя страница 25

Chapter 1: Overview

25

SFP Slots

The number of SFP slots and types of supported transceivers are given 
here:

Four SFP slots on the IE340-12GP, IE340-12GT and IE340-20GP 
switches

Two SFP slots on the IE340L-18GP switch

100Base-FX transceivers (All models except the IE340L-18GP 
switch.)

1000Base-SX/LX transceivers

Single-port Bi-directional (BiDi) 1000Base-LX transceivers

1000Base-ZX transceivers

1000Base-T twisted pair transceivers

Note

SFP transceivers are purchased separately. 

Protection

Circuits

The switches have optimized protection circuits to guard against the 
following abnormal conditions:

Reverse input voltage polarity

Over- and under-voltage

Over-current

Peak-current and short-circuit

Over-temperature

Alarm

Monitoring

The alarm facility lets you monitor the switch’s environment and respond to 
problems as they occur. Example of alarm events include:

Main power supply failure

Over-temperature

Port link down

Power requirements of all powered devices exceeding available 
power budget

Powered devices exceeding individual port budgets

External Alarm contact input

Alarm

Connectors

The switches have two alarm connectors:

Alarm In connector for an external sensor, such as a motion 
detector or door relay, to monitor the wiring closet or cabinet.

Alarm Out connector for an external alert device, such as a buzzer 
or LED, to indicate switch alarms.

Содержание IE340 Series









































































































































Отзывы:

Нет отзывов