Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 74 / 214

Chapter 2: Virtual Chassis Stacking

Switch ID Numbers

Each switch must be assigned an ID number. The range is 1 to 8 for a

stack with a trunk of AT-StackQS modules or the S1 and S2 ports. The

range is 1 to 4 when the stack trunk consists of the 1Gbps front panel

ports. The default is 1. The ID numbers are displayed on the ID LEDs on

the front panels of the units. You may assign the numbers yourself or let

the master switch assign the numbers automatically when you initially

power on the stack.

You use the ID numbers to identify the individual ports and switches when

you configure the devices with the commands in the management

software. For further information, refer to “Specifying Ports in the

Command Line Interface” on page 76.

The ID numbers are also used to identify the parameter settings that are

stored in the configuration file. When the stack is reset or power cycled,

the ID numbers identify the devices to which the parameter settings

belong.

Caution

You should not change the ID numbers of the switches after you

start to configure the parameter settings. Otherwise, the parameter

settings might be applied to the wrong devices when you reset or

power cycle the stack.



E79

The switches do not use their ID numbers to select the master switch. The

selection of the master switch is based on their priority numbers and MAC

addresses, as previously explained.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды