Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 72

Страница: 72 / 214

Chapter 2: Virtual Chassis Stacking

General Stacking Guidelines

Here are additional stacking guidelines:



Stacking is enabled by default on x930 Switches.



VCStack comes standard with the AlliedWare Plus software for

x930 Switches. No additional software or licenses are required.



The switches must all have the same version of AlliedWare Plus

software.



The switches can be the same or different x930 models.



Any x930 Switch can be the master switch of a stack.



A stack of x930 Switches cannot contain other stacking switches,

such as x600 or x610 Switches.



In stacks of three or more switches, all the switches must have the

same number of trunk ports.



Do not configure switch features, such as virtual LANs and routing

protocols, before building the stack. Switches might discard the

settings when the stack is powered on for the first time.



Trunk ports must be directly linked together. There cannot be any

intermediary devices, such as media converters, routers, or other

switches, between trunk ports.



Trunks cannot have different types of trunk ports. For example, a

trunk cannot have both Gigabit copper ports and ports S1 and S2.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды