Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 56

Страница: 56 / 214

Chapter 1: Overview

You can install only one AT-x9EM/XT4 Card in the switch. It replaces the

AT-FAN09ADP Module in the back panel. The installation instructions are

provided in Chapter 5, “Installing AT-StackQS and AT-x9EM/XT4 Cards”

on page 103.

Table 15. AT-x9EM/XT4 Card LEDs

LED

State

Description

L/A (Link/

Activity)

Off

The port is not connected to another

network device, the device is not powered

on, or the LEDs are turned off. To turn on

the LEDs, use the eco-friendly button.

Solid green

The port has established a 10Gbps link to

a network device.

Flashing

green

The port is transmitting or receiving

network traffic at 10Gbps.

Solid amber The port has established a 1Gbps link to a

network device.

Flashing

amber

The port is transmitting or receiving

network traffic at 1Gbps.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды