Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 28

Страница: 28 / 214

Chapter 1: Overview



Installing two power supplies adds power redundancy.



The power supplies are not recommended for the PoE+ AT-x930-

28GPX and AT-x930-52GPX Switches because they do not supply

power for PoE+ devices. You may install them into PoE+ switches,

but the switches will not support powered devices.

System and PoE+

Power Supplies

The AT-PWR800 and AT-PWR1200 Power Supplies provide both system

power and power for PoE+ devices on AT-x930-28GPX and AT-x930-

52GPX Switches. Refer to Figure 7.

Figure 7. AT-PWR800 and AT-PWR1200 Power Supplies

A PoE+ switch with one AT-PWR800 Power Supply has the following

power characteristics:



Full system power



380 watts of PoE+ power

A PoE+ switch with two AT-PWR800 Power Supplies has these power

characteristics:



Full system power and redundant system power



Either 740 watts of PoE+ power or 380 watts of active PoE+ power

and 380 watts of redundant PoE+ power.

A PoE+ switch with one AT-PWR1200 Power Supply has the following

power characteristics:



Full system power



740 watts of power for PoE devices

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды