background image

Quick Install Guide

3

C613-04038-01 REV F

Models Covered By This Guide

This Quick Install Guide includes information on the following models:

AT-9812T

AT-9812TF

AT-9816GB

AT-9816GF

Quick Install Guide updates can be downloaded from 
www.alliedtelesyn.co.nz/support/at9800/

Package Contents

The following items are included with each AT-9800 Series switch. Contact 
your sales representative if any items are damaged or missing.

One AT-9800 Series switch

One AC power cord (for AC models)

One serial cable for connecting the switch to a terminal or PC

One 19 inch rack-mount kit

One AT-9800 Series Quick Install Guide

One Safety and Statutory Information booklet

One AT-9800 Series Documentation and Tools CD-ROM (which includes 
the complete AT-9800 Series Document Set and utilities)

One warranty card

CAM

AT-9800 Series

Printed

Acrobat PDF

Website

Documentation Roadmap

AT-9800 Series Safety and Statutory Information Booklet

AT-9800 Series Software Reference

AT-9800 Series Hardware Reference

General Customer Support

Visit www.alliedtelesyn.co.nz for 
the latest documentation, FAQs, 
and support information.

AT-9800 Series Quick Install Guide

CAM Quick Install guide

AT-RPS9000 Quick Install Guide

AT-RPS9000 Safety and Statutory Information Booklet

Содержание AT-9800 Series













Отзывы: