Allied Telesis AT-8900 SERIES Скачать руководство пользователя страница 3

Patch 89262-08 For AT-8900 Series Switches

3

Patch 89262-08 for Software Release 2.6.2
C613-10402-00 REV H

 

When STP is enabled, when frames with a multicast destination MAC 
address were sent, a loop was observed within the network. This issue has 
been resolved.

 

In network configurations with multiple paths to neighbours on an 
interface, if the interface changed state from up to down, then up again, the 
interface route may have been erroneously deleted by a route update. This 
issue has been resolved. 

 

The 

valid

 and 

preferred

 parameters were incorrectly added to the dynamic 

set ipv6 prefix

 configuration. The default 

onlink

 and 

autonomous

 

parameters were also being included. This issue has been resolved.

Level 3

 

The 

counter

 parameter did not exist in the 

show igmpsnooping

 command. 

This issue has been resolved.

 

An error message is now shown if the user tries to assign more than the 
allowable number of traffic class (or default traffic class) entries to active 
QOS policies.

 

When a Core port was added to a nested VLAN, its Ingress Filtering 
attribute was set to be On and Acceptable Frame Type was set to be Admit 
Only VLAN tagged Frames. If the port was deleted from that VLAN, its 
Ingress Filtering attribute must be set to Off and Acceptable Frame Type 
must be set to Admit All Frames, however, the attributes were not changed 
when the port was deleted from the nested VLAN. This issue has been 
resolved.

 

The manager prompt did not appear when using a telnet session until the 
[Enter] key was pressed several times. This issue has been resolved.

 

An FTP server located on a private interface of a firewall with NAT enabled 
may have had its ftp-data (tcp/20) source port translated to another port. 
This could lead to a firewall rejecting the data packets, as they do not strictly 
conform to RFC 959. This issue has been resolved, ensuring that ftp-data 
packets are sent from port 20 on the firewall, even when NAT is enabled.

PCR: 40596

Module: SWMX

                                  Level: 2

PCR: 40601

Module: SWMX

                                  Level: 2

PCR: 40619

Module: IPG

                                  Level: 2

PCR: 40589

Module: IPG

                                  Level: 3

PCR: 40603

Module: SWI, SWMX

                                  Level: 3

PCR: 40606

Module: VLAN

                                  Level: 3

PCR: 40617

Module: TTY

                                  Level: 3

PCR: 40618

Module: SWI

                                  Level: 3

Содержание AT-8900 SERIES

































Отзывы: