ALLIANCE SWNNC2HP115TQ01 Скачать руководство пользователя страница 78

Страница: 78 / 90

Configura-

tion Value

Life Test

Jumper

Present

Comm

Board "B"

Header

Present

Comm

Board "A"

Header

Present

Vend Con-

nection

Present

Coin Drop

#2 Present

Coin Drop

#1 Present

YES

Table 15

Configuration 2 Display Test

d 30

This option is not used on this model.

Configuration 3 Display Test

d 31

This option is not used on this model.

Configuration 4 Display Test

d 32

This option shows the user which dipswitches are set on the con-
trol.

To start test, control must be in the Testing Mode. Refer to

How

to Enter Testing Feature

at the beginning of this section.

To Enter, press the START (enter) keypad. The display will show

XXX with XXX representing a configuration value as shown

Table 16

If supply voltage is 100-127 Volt per phase, the voltage configu-
ration should be 120 Volt.

If supply voltage is 200-240 Volt per phase, the voltage configu-
ration should be 240 Volt.

To exit Machine Configuration 4 Display Test, press the WARM
(<) keypad. The control will return to the Testing Mode.

Each column in the table below contains a unique combination of
the words “ON” and “OFF” that indicates if that column’s dips-
witch is set on or off when the value is displayed. All other dips-
witches are not used.

Configuration Value

Dipswitch 3

Payment System Not Present
(OFF)

Payment System Present (ON)

Dipswitch 1

120 Volt Supply (OFF)

240 Volt Supply (ON)

OFF

Table 16

Configuration 5 Display Test

d 33

This option is not used on this model.

Testing Machine and Electronic Control Functions

DO NOT COPY or TRANSMIT

Part No. 204370ENR1

Содержание SWNNC2HP115TQ01



























































































Результаты поиска

Содержание SWNNC2HP115TQ01

Отзывы:

Похожие инструкции для SWNNC2HP115TQ01

Бренды по названию

Популярные бренды

ALLIANCE SWNNC2HP115TQ01, Оригинальное руководство пользователя

Результаты поиска

Содержание SWNNC2HP115TQ01

Отзывы:

Похожие инструкции для SWNNC2HP115TQ01

Бренды по названию

Популярные бренды