background image

 

14

 
WARRANTY 

 
 

   One year on parts – 90 days on labor. 

 

Alliance provides to the original purchaser, only, a warranty for the DALPH1022.  This 
warranty covers products and parts which prove to be defective in materials or 
workmanship within one (1) year of the date of shipment from the ALLIANCE factory.  
Repair or replacement will be at the option of ALLIANCE and will be f.o.b. the 
ALLIANCE factory.  Warranty includes ninety (90) days for labor from date of 
shipment.  Prior written authorization from the ALLIANCE customer service 
department is required before any component parts or equipment can be accepted by 
ALLIANCE for repair, replacement, or credit under this warranty.  This warranty shall 
not apply if it is determined by ALLIANCE that equipment or parts have been used 
other than in accordance with the operating instructions, subject to abuse or misuse, 
damage through no fault of ALLIANCE or its employees, or altered by someone other 
than ALLIANCE or its authorized agents.  This warranty is exclusive and in lieu of all 
other warranties express or implied, or statutory, including the implied warranties of 
merchantability and fitness.  In no event shall ALLIANCE be liable for any delay in the 
performance of this warranty due to causes beyond its control. 

 
 

SERVICE AND ASSISTANCE 

 
 

In Warranty Service 

– Call the Alliance Customer Service Department at 

1-800-522-

3973

.   Parts are stocked at the factory and will be provided to a local authorized 

service agency. 
 

Out of Warranty Service

 – Same as above except parts will be billed to the customer 

or the service agency as dictated by the customer.  Labor will be billed by the agency. 
 

Technical Assistance

 – Write down the nature of the problem and any symptoms along 

with any other information that might prove helpful in solving your problem.  Then call 
the Alliance Customer Service Department at 

1-800-522-3973

 
 
 
 
 
 
 
 

Содержание DALPH1022
















Отзывы: