Alliance Laundry Systems UL15F069 Скачать руководство пользователя | Manualshive

Страница: 6 / 27

background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

1800001

4

Safety

Explanation of Safety Messages

Safe operating and maintenance practices presented in
this manual are emphasized with special safety
messages. These messages are categorized as
DANGER, WARNING and CAUTION. Explanations
of these categories are listed below.

These safety messages are used throughout this
manual to identify safe practices. Signal words are
placed with descriptions or steps where the need to
maintain safe conditions is critical.

Safety signs and labels are also placed on the unit.
Those signs and labels are limited messages. These
signs are to be inspected for readability and replaced
when missing, damaged, or unreadable. Refer to the

Maintenance

section of this manual for the periodic

maintenance schedule. Refer to the parts manual for
ordering information.

IMPORTANT: The word "IMPORTANT" is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.

NOTE: The word "NOTE" is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.

The WARNING and IMPORTANT instructions
appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It
must be understood that common sense, caution and
carefulness are factors which CANNOT be built into
this finisher. These facts MUST BE supplied by the
person(s) installing, maintaining or operating the
finisher.

Always contact your dealer, distributor, service agent
or the manufacturer on any problems or conditions you
do not understand.

Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.

DANGER

Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.

WARNING

Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.

CAUTION

«
...
4
5
6
7
8
...
»

Содержание UL15F069




























Отзывы:

Нет отзывов

Похожие инструкции для UL15F069

Бренд: Delta Страницы: 12

Бренд: Delta Страницы: 76

Бренд: AFINIA LABEL Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды