background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Installation

1800001

12

Electrical Connection

Electrical connections should be made by a qualified 
electrical contractor in accordance with all applicable 
local and national requirements. A differential circuit 
breaker (obtain locally), correctly sized for the power 
consumption of the finisher, must be installed near 
finisher. Refer to 

Table 3

 and 

Table 4. 

IMPORTANT: Electrical specifications in 

Table 3

 

and 

Table 4

 are subject to change without notice. 

Always refer to product serial plate for most 
current specifications of product being installed.

NOTE: Use copper conductors only.

NOTE: Connect to individual branch circuit.

 

Before preceding, check for proper rotation of exhaust 
fan, hydraulic pump, and circulation pump. All three 
should be moving in the direction indicated by the 
arrow on part. If all three are rotating properly 
proceed. If they are not, reverse polarity of component 
not rotating properly.

Electrical Models 

(CE Approved)

Serial Plate Rating

Model

Recommended
Circuit Breaker

Heater Element

All Voltages

UL15*069

50 Amp

40 hp (30 kW)

UL15*079

50 Amp

40 hp (30 kW)

UL15*099

57 Amp

47 hp (35 kW)

UL15*118

63 Amp

54 hp (40 kW)

UL20*079

50 Amp

40 hp (30 kW)

UL20*099

63 Amp

54 hp (40 kW)

UL20*118

70 Amp

60 hp (45 kW)

UL20*130

70 Amp

60 hp (45 kW)

Table 3 

All Gas Models 

(CSA and CE Approved)

Serial Plate Rating

Recommended
Circuit Breaker

Full Load Amps

230/50/3 

208-240/60/3

30 Amp

28 Amp

400/50/3

20 Amp

16 Amp

440-480/60/3

15 Amp

14 Amp

Table 4 

Содержание UL15F069




























Отзывы:

Похожие инструкции для UL15F069