care label. The time may need to be adjusted up if the items
are still damp or down if the items are overdry.
To use, set Cycle Selection to Time Dry (30 minutes or 60 mi-
nutes) and set the Fabric Selector to the proper temperature
for the type of load. The Auto-Dryness setting is ignored unless
Dry & Extended tumble is selected.
Steam Refresh
Steam Refresh, releases wrinkles and refreshes items. It is
recommended for small loads of 1-4 items. There are two pre-
set cycles. The default cycle applies a medium-temperature
heat for 30 minutes to the load. The alternate cycle applies a
high-temperature heat for 20 minutes.
To use, set the Cycle Selection to Steam Refresh. Setting the
Fabric Selector to Delicate, Perm Press or Regular initiates the
30 min, medium heat cycle. If the Fabric Selector is set to
Heavy Duty, the 20 min, high heat cycle is initiated. Auto-Dry-
ness is ignored unless set to Dry & Extended Tumble.
IMPORTANT: Do not use dryer sheets when using
steam cycles.
IMPORTANT: Do not run steam with no load to help
prevent water from staining the cylinder.
NOTE: Do not overload machine for steam cycles.
Overloading during a steam cycle may cause the load
to have wet spots at the end of the cycle.
NOTE: Using steam on overly damp items may result in
load not completely drying.
Auto-Dryness
Use the Auto-Dryness selections to select the dryness level.
Less Dry, which uses the least energy, will dry large loads and
lightweight items, such as sheets and shirts, but might leave
other items, such as denim and heavy bath towels, more
damp.
Near Dry*, will stop the cycle when items are slightly damp.
Certain fabric labels recommend removing items from the dry-
er before they are completely dry to help prevent shrinking and
wrinkling.
Dry, will dry very small loads and some heavy items, such as
blue jeans, but will overdry lightweight items, such as sheets
and shirts. Overdrying can cause wrinkling, shrinking, exces-
sive lint conditions, and will use more energy than necessary.
Dry & Extended Tumble will dry very small loads and some
heavy items, such as blue jeans, but will overdry lightweight
items, such as sheets and shirts. Overdrying can cause wrin-
kling, shrinking, excessive lint conditions, and will use more
energy than necessary. The EXTENDED TUMBLE setting contin-
ues to tumble items at no heat after the cycle has completed.
This prevents wrinkling when garments cannot be removed
from the dryer immediately.
The Energy Saver settings, marked with an asterisk(*), show
which settings will use the least energy and will leave items
damp for easier ironing.
The Cooling period at the end of each cycle provides items a
chance to tumble with no heat and cool down to room temper-
ature. This prevents wrinkles from setting if items cannot be
cared for immediately.
Over-drying can cause wrinkling, shrinking, excessive lint con-
ditions, and will use more energy than necessary. To increase
energy savings and to make sure loads are dried without over-
drying, set your Auto-Sensing loads on Near Dry* or Less Dry.
If items are damp or over-dry at the end of a cycle, increase or
decrease the Dryness setting the next time these loads are
dried. Remember the settings that work best to get ideal dry-
ing results.
Fabric Selector
The type of heat is determined by selecting the proper Fabric
Selector option.
1. DELICATE uses low heat, use to dry delicate items.
2. PERM PRESS uses medium heat, use for permanent press
items and synthetics.
3. REGULAR uses medium-high heat, use for sturdy items like
play or work clothes.
4. HEAVY DUTY uses high heat, use for heavy items such as
blankets.
Steam Boost
Steam Boost, releases wrinkles and soften fabrics. It is availa-
ble with Auto-Sensing Heavy Duty, Regular, and Perm Press cy-
cles as well as Sanitize. Auto-Dryness must be set to Near Dry
or Dry.
NOTE: The Steam Boost option is not available with the
energy saving setting - Auto-Sensing, Regular, Near
Dry*.
Status
The Status lights are lit during the cycle to show what part of
the cycle is running.
1. The HEATING status light is lit to indicate that a heat por-
tion of the cycle is currently operating.
2. The COOLING status light is lit during the cool-down portion
of the cycle.
3. The EXTENDED TUMBLE status light is lit during the Dry &
Extended Tumble cycle.
4. The DOOR OPEN status light is lit any time that the dryer
door is open.
To Dry Clothes
Operating Your Dryer
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11
Part No. D518673EN
Содержание Huebsch DR5
Страница 2: ......
