Alliance Laundry Systems 510988R3 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 30

Alliance Laundry Systems 510988R3 Скачать руководство пользователя страница 24

Operation

510988

22

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

To Dry Clothes

IMPORTANT: Refer to the INSTALLATION
INSTRUCTIONS before using dryer.

NOTE: This appliance is designed for repeated
normal operation according to operating
instructions.

1. Sort items into separate loads.

IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.

Figure 17

2. Remove lint filter cover, clean lint filter and

replace cover.

Figure 18

3. Add clothes loosely into dryer drum. Add fabric

softener sheet, if desired.

NOTE: To avoid damage to dryer, do not use more
than one fabric softener sheet per load.

Figure 19

4. Close loading door. Dryer will not operate with

the door open.

Figure 20

5. Select FABRIC SELECTOR. Follow garment

manufacturer’s care labels for recommended
temperature settings.

6. Select timer setting in cycle desired:

AUTOMATIC REGULAR/DELICATE, TIME
DRY, and AUTOMATIC PERMANENT PRESS/
KNITS. These cycles control the drying time.

The ENERGY SAVER/DAMP DRY settings, marked
with a dot (

•

), show which dryer settings will use the

least energy and will leave items damp for easier
ironing.

7. Push timer knob in to start dryer.

NOTE: To stop dryer at any time, open the door or
turn timer knob to an OFF position. To restart
dryer, close door, reset timer if necessary, and push
in the timer knob.

D305IE1A

D689IE0A

D689IE0A

D666IE0A

D668IE0A

D666IE0A

D668IE0A

«
...
22
23
24
25
26
...
»

Содержание 510988R3































Отзывы:

Нет отзывов