allen BDF6048B Скачать руководство пользователя страница 8

053016

Page 8

SECTION 1

INTRODUCTION

Section 1

BATTERY PRECAUTIONS

1 .  Keep all sparks and flames away from battery, as gas given off 

by electrolyte is explosive.

2 .  If you come in contact with battery electrolyte solution wash off 

immediately .

3 .  Always disconnect the battery ground cable before working on 

the electrical system .

4 .  Do not tip battery more than 45 degrees to avoid electrolyte loss .

TRANSPORT PRECAUTIONS

1 .  Consult the 6048 Operator’s Manual before attempting to lift your 

paver. Use extreme caution when lifting the machine. Make sure 

that the lifting device has enough capacity to lift the weight of the 
machine . Check all lifting cables, chains, clevises, cable clamps 
and spreader beams for any damage . Use ropes tied to the ends 
of the machine to prevent the machine from spinning . Keep all 
personnel away from the machine while it is being lifted .

2 .  Always comply with local regulations regarding moving equip-

ment on public roads and highways .

3 .  Make sure that all lights and reflectors comply with state and 

local regulations . Make sure that they are clean, in good working 
order and can be seen clearly by all overtaking and on-coming 
traffic .

STORAGE PRECAUTIONS

1 .  Store paver in an area away from human activity .
2 .  Do not permit children to play on or around the stored paver .
3 .  Make sure the unit is stored in an area that is firm, level and free 

of debris .

4 .  Store the paver inside a building or cover securely with a weath-

erproof tarpaulin .

SAFETY DECALS

1 .  Keep Safety Decals and signs clean and legible at all times .
2 .  Replace decals and signs that are missing or become impossible 

to read .

3 .  When replacing parts that previously displayed a safety decal, be 

sure to replace the decal as well .

4 .  Obtain Safety Decals or signs from the Allen Parts and Service 

Department .

5 .  Become familiar with the content and the position of each Safety 

Decal . Important information is written on the decals .

Introduction

Содержание BDF6048B











































Отзывы: