allen 070080 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 62

background image

b) Speed control return spring. This spring is mounted on the transmission shift bar and allows the speed control

lever to return automatically when released. Spring tension should be sufficient to briskly snap back the speed

control lever when it is released. Broken, damaged, or deformed springs must be replaced immediately.

Note: never

bend, otherwise modify, or attempt to repair this spring

.

Due to the critical nature of the Speed Control Return Spring - replacement is recommended every 24

months or sooner for use in extreme conditions.

In all cases, upon release of the speed control lever, the speed control linkage should
operate smoothly and freely and stop machine travel within 6 - 8’ in both forward and
reverse.

If the speed control linkage does not operate smoothly and freely and/or does not

automatically stop machine travel upon release of the speed control lever, then remove
machine from service until repairs have been made.

c) The mechanical service and parking brake. The mechanical service brake is designed
to act as a reserve system to the primary dynamic hydrostatic braking provided by the
hydrostatic transmission. Properly maintained and adjusted mechanical service brakes
will stop a fully loaded machine traveling at full speed in the event of failure of the speed
control system or loss of hydraulic pressure. A properly maintained and adjusted parking
brake will hold a fully loaded buggy in position. Please see “Machine Adjustments” in this
manual for adjustment procedures.

d) Verify that all safety and instruction labels are intact and legible.

5) Inspect lug nuts for proper torque (see Safety and Operation Requirement Chart)

6) Inspect tires, wheels and tire pressure (see Safety and Operation Requirement Chart), and tracks on machines
so equipped.

7) Inspect the following controls for proper adjustment, cleanliness and operation: bed dump valve and dumping
mechanism, directional control valve, dash mounted EMERGENCY stop switch, and steering assembly. Immedi-
ately remove from service any machine on which these controls are not adjusted and operating properly.

8) Inspect: engine oil level, hydraulic oil level. Add Fluids as required. Repair all leaks. Follow all maintenance as
outlined in the SERVICE section of this manual.

General Safety

SECTION 1

SAFETY

069583

Page 18

«
...
16
17
18
19
20
...
»

Содержание 070080































































Отзывы:

Нет отзывов

Похожие инструкции для 070080

Low Loader Trailer

Бренд: Futura Страницы: 20

Off-Roader 36EL

Бренд: Texas Страницы: 27

Beast 1000 Series

Бренд: BMS Страницы: 114

MAVERICK Sport MAX 1000R

Бренд: Can-Am Страницы: 187

RANGER XP 1000 2018

Бренд: Polaris Страницы: 565

Бренд: Humbaur Страницы: 48

Бренд: Jacobsen Страницы: 76

Бренд: Labrie Страницы: 145

Бренд: NC Страницы: 79

Бренд: Chapman Страницы: 27

Бренд: Landa Страницы: 38

Бренд: Landa Страницы: 101

Бренд: YX Motors Страницы: 159

Бренд: PARKIT360 Страницы: 13

Бренд: Primo Water Страницы: 12

FOURTRAX 350 4x4 2001

Бренд: Honda Страницы: 169

Бренд: Honda Страницы: 227

1990 TRX200 Fourtrax200

Бренд: Honda Страницы: 149

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды