This kit provides space for exposed storage
beside base and peninsula base cabinets.
Fits
shelf end base (seb) can be installed next
to any base or peninsula base cabinet. seb
toe kick can be installed for left or right
application. sepb can be installed next to
any peninsula base cabinet.
SEB Contents
• Shelf End Base (SEB)
• Toe Kick Unit (not attached)
• (2) #8 x 1-1/8” Mounting Screws
SEPB Contents
• Shelf End Peninsula Base (SEPB)
• Toe Kick Unit (not attached)
• (2) #8 x 1-1/8” Mounting Screws
Tools Needed
• Phillips Screwdriver
• Drill
• Pencil
• 3/32” and 5/32” Drill Bits
Additional Items Needed
(not included)
• (4) #8 x 7/8” Phillips Pan Head Screws
for 1/2” thick Side Panels
• (4) #8 X 1-1/8” Phillips Pan Head
Screws for 3/4” thick Side Panels
• 3/4” Wire Brads (for extended SEB
configuration)
Shelf End Base
(SEB)
& Shelf End Peninsula Base
(SEPB)
For Use Beside Base and Peninsula Base Cabinets
place toekick so that it lines up
with the toekick of the adjacent
cabinet. Position the SEB/SEPB
against the adjacent cabinet and
on top of the toe kick. Trace the
edge of the toekick on the bottom
of the SEB/SEPB.
Turn the SEB/SEPB upside down
and put aside temporarily. in the
top of the toe kick, drill two
5/32” holes opposite the large
holes in the bottom. next, place
the toekick onto the overturned
SEB/SEPB and align with the
previously traced marks. Then mark the hole locations on the SEB/SEPB bottom. Drill pilot
holes at the marked positions, 3/32” diameter x 3/8” deep.
CAUTION: BE CAREFUL NOT TO DRILL THROUGH!
Use #8 x 1-1/8” screws
(provided) and attach toe kick unit to SEB/SEPB.
HINT:
Wrapping a piece of tape around
the drill bit 7/8” from the end (1/2” for toe kick top thickness plus 3/8” noted above) will
give a visual stopping point for the correct depth to drill.
Drill four 5/32” diameter holes through the side of the cabinet adjacent to the shelf unit.
They should be evenly spaced top to bottom and side to side near each corner. put seb
or SEPB into place, aligning the toe kick with toekick of adjacent cabinet. Mark drilled
locations through cabinet sides and drill pilot holes 3/32” diameter x 3/8” deep in shelf
unit at these positions.
CAUTION: BE CAREFUL NOT TO DRILL THROUGH!
Use (4) #8 x 7/8” screws (not
included for 1/2” Side Panels) or #8 X 1-1/8” screws (not included for 3/4” Side Panels)
to attach the SEB/SEPB to the adjacent cabinet, and your new SEB/SEPB cabinet is ready
to use.
1
2
3
Procedure
Shelf End Base (SEB)
Shelf End Peninsula Base (SEPB)
NOTE:
Two SEB units are
needed for this configuration
and they must be attached to
each other as well as to the
adjacent cabinet.
See Steps 1–3 for attachment
to the adjacent cabinet.
Use (3) 3/4” wire brads (not
included) to attach the seb
units together.
Extended SEB Configuration
99921 1/10
Installation Instructions
Read carefully before you begin installation
These insTrucTions should noT be fAxed or reproduced on A digiTAl copier. AmericAn WoodmArk corporATion provides These insTrucTions on An “As is” bAsis And disclAims Any And
All liAbiliTy for Any inAccurAcies, omissions or TypogrAphicAl errors cAused by Any Third pArTy’s equipmenT. When you use these instructions, you are consenting to be bound by the provisions
in this paragraph. These instructions provide an illustrative method for installing American Woodmark Corporation (“AWC”) cabinets and/or accessories. AWC’s instructions are not intended to address every possible
contingency that might be encountered during installation or to endorse the use of any particular tools. AWc hereby expressly disclAims All liAbiliTy for Any clAims for inJury or deATh relATed To or
bAsed upon The use of These insTAllATion insTrucTions And Any insTAllATion insTrucTions oTherWise provided by AWc.
Shelf End Base
Figure 1
Adjacent
Peninsula
Base Cabinet
3/4" Wire Brads
Figure 2
SEB
SEB
Top View
Shelf End Base
Figure 2
Figure 1
Adjacent
Base
Cabinet
SEB
SEPB
Adjacent
Peninsula
Base Cabinet
#8 x 7/8" Screw (4 required per unit
for 1/2" thick Side Panel)
#8 x 1-1/8" Screw (4 required per
unit for 3/4" thick Side Panel)
Adjacent
Base
Cabinet
SEB
Toe Kick Unit
Top View
Top View
#8 x 7/8" Screw (4 required per
unit for 1/2" thick Side Panel)
#8 x 1-1/8" Screw (4 required per
unit for 3/4" thick Side Panel)
#8 x 7/8" Screw
(4 required per unit for
1/2" thick Side Panel)
#8 x 1-1/8" Screw
(4 required per unit for
3/4" thick Side Panel)
