Allen-Bradley POINT I/O 1734-OE2C Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

Allen-Bradley POINT I/O 1734-OE2C Скачать руководство пользователя страница 17

POINT I/O 2 Current Output and 2 Voltage Output Analog Modules

17

Publication 1734-IN002E-EN-E - October 2016

Module Status

Indication

Probable Cause

Off

No power is applied to device.

Green

Device is operating normally.

Flashing Green

Device needs commissioning due to configuration missing, incomplete, or
incorrect.

Flashing Red

Recoverable fault is present.

Red

Unrecoverable fault may require device replacement.

Flashing Red/Green

Device is in self-test.

Network Status

Indication

Probable Cause

Off

Device is not online.
- Device has not completed dup_MAC_id test.
- Device not powered. Check module status indicator.

Flashing Green

Device is online but has no connections in the established state.

Green

Device is online and has connections in the established state.

Flashing Red

One or more I/O connections are in timed-out state.

Red

Critical link failure is present with failed communication device. Device
detected error that prevents it communicating on the network.

Flashing Red/Green

Communication faulted device is present.
The device detected a network access error and is in communication faulted
state.
Device received and accepted an Identify Communication Faulted Request -
long protocol message.

Channel Status

Indication

Probable Cause
1734-OE2C

Probable Cause
1734-OE2V

Off

Module is in CAL mode.

Green

Normal operation is present with channel actively controlling outputs.

«
...
15
16
17
18
19
...
»

Содержание POINT I/O 1734-OE2C























Отзывы:

Нет отзывов