Allen-Bradley POINT I/O 1734-IE2C Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

Allen-Bradley POINT I/O 1734-IE2C Скачать руководство пользователя страница 11

POINT I/O 2 Current and 2 Voltage Input Analog Modules

11

Publication 1734-IN027C-EN-E - October 2016

Remove a Mounting Base

To remove a mounting base, you must remove any installed module and the module that is
installed in the base to the right. Remove the removable terminal block, if wired.

1. Unlatch the RTB handle on the I/O module.

2. Pull on the RTB handle to remove the removable terminal block.

3. Press the module lock on the top of the module.

4. Pull on the I/O module to remove from the base.

5. Repeat steps 1, 2, 3 and 4 for the module to the right.

6. Use a small bladed screwdriver to rotate the orange base locking screw to a vertical

position. This releases the locking mechanism.

7. Lift straight up to remove.

WARNING:

For 1734-TOPS and 1734-TOP3S, to latch and un-latch the wire,

insert a bladed screwdriver (catalog number 1492-N90 – 3 mm diameter) into
the opening at approximately 97° (blade surface is parallel with top surface of
the opening) and press in (do not push up or down).

97°

«
...
9
10
11
12
13
...
»

Содержание POINT I/O 1734-IE2C























Отзывы:

Нет отзывов