manualshive.com logo in svg

Allen-Bradley ControlNet 1786-RPFRL/B, Руководство по установке, Страница: 17 / 40

Поделиться
Скачать
Allen-Bradley ControlNet 1786-RPFRL/B Скачать руководство пользователя страница 17

ControlNet Fiber-optic Ring Repeater Modules    

17

Rockwell Automation Publication  1786-IN003D-EN-P - April 2011

8.

Reinsert the power supply connector into the 1786-RPA/B module.

Install the Ferrite at the Relay Contact Connector

1.

Use the key to open the remaining ferrite.

2.

Form a loop with both wires (+ and -) approximately 100 mm (4.0 in.) 
away from the relay contact connector of the 1786-RPFRL/B or 
1786-RPFRXL/B module.

3.

Loop the wires through the ferrite.

4.

Close the ferrite.

Be careful not to damage the wires.

5.

Strip approximately 6 mm (0.24 in.) of wire from the end that will 
connect to the relay contact connector on the 1786-RPFRL/B or 
1786-RPFRXL/B module.

6.

Remove the relay contact connector from the 1786-RPFRL/B or 
1786-RPFRXL/B module.

7.

Install the stripped ends of the wires in the relay contact connector on 
the fiber repeater module as shown below.

8.

Reinsert the relay contact connector into the 1786-RPFRL/B or 
1786-RPFRXL/B module.

Connect the Ferrite Here

Spare Allen-Bradley Parts

Содержание ControlNet 1786-RPFRL/B









































Отзывы:

Нет отзывов