Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 144

background image

1

Publication 1756-UM050A-EN-P - December 2001

Appendix

C

Configuring the RSLinx Ethernet
Communication Driver

What This Appendix
Contains

In order to communicate with your 1756-ENBT modules over your
network you must configure the RSLinx Ethernet communication
driver (AB_ETH). You can configure the AB_ETH driver with the IP
addresses of all the Ethernet modules on your system. You will need
this driver to download the example application programs in this
manual.

The following table lists the contents of this appendix and where to
find specific information:

Installing the RSLinx
Software

Use the following procedure to install RSLinx software on your
computer.

1.

Insert the CD in the CD-ROM drive.

Note:

The CD-ROM supports Windows Autorun. Once inserted into

the CD-ROM drive, if you have Autorun configured, the installation
will automatically start at the first setup screen.

If Autorun is not configured for your CD-ROM drive, go to step 2.

2.

From the

Start

menu, choose

Run

.

You will see the Run pop-up window.

3.

Type

d:/setup

(if it doesn’t appear automatically), where

d:

is your

CD-ROM driver letter.

4.

Click on

OK

.

You will see the progress bar, followed by the welcome screen.

For information about

See page

Installing the RSLinx Software

Configuring the AB_ETH Driver

«
...
119
120
121
122
123
...
»

Содержание ControlLogix 1756-ENBT

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ControlLogix 1756-ENBT

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: BADLANDS Страницы: 2

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Yamaha Страницы: 92

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: LOGICDATA Страницы: 23

Бренд: A10 Networks Страницы: 2

Бренд: Z-Wave Страницы: 5

Бренд: KAR-TECH Страницы: 55

10 AMP RVC-MPPT

Бренд: Go Power Страницы: 17

DX99N9X1S2N0M2X0D2

Бренд: Banner Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды