Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 116

background image

Publication 1769-UM005A-EN-P

Diagnostics and Troubleshooting

5-3

Power-up Diagnostics

At module power-up, a series of internal diagnostic tests are performed.
These diagnostic tests must be successfully completed or the module
status LED remains off and a module error results and is reported to the
controller.

Channel Diagnostics

When an input channel is enabled, the module performs a diagnostic
check to see that the channel has been properly configured. In addition,
the channel is tested on every scan for configuration errors, over-range
and under-range, and broken input conditions.

Invalid Channel Configuration Detection

Whenever a channel configuration word is improperly defined, the
module reports an error. See pages 5-4 to 5-7 for a description of module
errors.

Out-of-Range Detection

When the input signal data received at the channel word is out of the
defined operating range, an over-range or under-range error is indicated
in input data word 7.

Possible causes for an out-of-range condition include:

•

The temperature is too hot or too cold for the RTD being used.

•

The wrong RTD is being used for the input type selected, or for the
configuration that you have programmed.

•

The input device is faulty.

•

The signal input from the input device is beyond the scaling range.

If module status
LED is:

Indicated
condition:

Corrective action:

On

Proper Operation

No action required.

Off

Module Fault

Cycle power. If condition persists, replace the module.
Call your local distributor or Rockwell Automation for
assistance.

IMPORTANT

There is no under-range error for direct resistance inputs
because 0 is a valid number.

«
...
75
76
77
78
79
...
»

Содержание Compact 1769-IR6





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact 1769-IR6

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Quantum Страницы: 97

Бренд: FAIE Страницы: 5

Бренд: CAME Страницы: 32

Бренд: M-system Страницы: 7

Бренд: Optimus Страницы: 44

Бренд: ZKTeco Страницы: 56

IP Solutions VIP-172L

Бренд: Valcom Страницы: 4

Бренд: Curtis Страницы: 24

4.3" Video Door Phone

Бренд: Alarmtec Страницы: 14

Бренд: Hallins Страницы: 17

Бренд: Hago Страницы: 7

Audio Everywhere

Бренд: Listen Technologies Страницы: 2

Бренд: pewag Страницы: 24

Бренд: Valcom Страницы: 4

Бренд: RCA Страницы: 19

GIOTTO 30-50 BT

Бренд: BFT Страницы: 21

SENTEX Infinity B Series

Бренд: Chamberlain Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды