Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 116

background image

Publication 1769-UM005A-EN-P

4-12

Module Data, Status, and Channel Configuration

Engineering Units x 1 Data Format

If you select engineering units x 1 as the data format for an RTD input, the
module scales input data to the actual temperature values for the selected
RTD type per RTD standard. It expresses temperatures in 0.1

°°°°

C units. For

resistance inputs, the module expresses resistance in 0.1

Ω

units, for all

ranges except the 150

Ω

range. For the latter, resistance is expressed in

0.01

Ω

units.

The resolution of the engineering units x 1 format is dependent on the
range selected and the filter selected. See Determining Effective
Resolution and Range on page 4-19.

Engineering Units x 10 Data Format

For the engineering units x 10 data format for an RTD input, the module
scales input data to the actual temperature values for the selected RTD
type per RTD standard. With this format, the module expresses
temperatures in 1

°°°°

C units. For resistance inputs, the module expresses

resistance in 1

Ω

units, for all ranges except the 150

Ω

range. For the latter,

resistance is expressed in 0.1

Ω

units.

The resolution of the engineering units x 10 format is dependent on the
range selected and the filter selected. See Determining Effective
Resolution and Range on page 4-19.

Scaled-for-PID Data Format

If you select the scaled-for-PID data format, the module presents to the
controller a signed integer representing the input signal range
proportional to the selected input type. The integer value is the same for
RTD and resistance input types.

To obtain the value, the module scales the input signal range to a
linearized 0 to 16383 range, which is standard to the PID algorithm for the
MicroLogix, SLC, and PLC controllers. The 0 value corresponds to the
lowest temperature or resistance value, while 16383 corresponds to the
highest value. For example, if a 100

Ω

platinum 385 RTD is selected, the

lowest temperature for the RTD, -200

°°°°

C, corresponds to 0. The highest

temperature, 850

°°°°

C, corresponds to 16383.

NOTE

Use the engineering units x 10 setting to produce
temperature readings in whole degrees Celsius or
Fahrenheit. See Engineering Units x 10 Data Format
below.

«
...
50
51
52
53
54
...
»

Содержание Compact 1769-IR6





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact 1769-IR6

Бренд: Safeline Страницы: 20

Бренд: DayTronic Страницы: 414

Бренд: Bticino Страницы: 84

Бренд: Onn Страницы: 11

Бренд: Medion Страницы: 308

Бренд: Aiphone Страницы: 4

tyco AQUAMIST ULF AM33

Бренд: Johnson Controls Страницы: 4

Бренд: The Fisher Страницы: 20

RM-208 CB.13.01

Бренд: EasyLine Страницы: 16

Бренд: ICP DAS USA Страницы: 8

Бренд: Atlas Страницы: 3

Autoscript WHC-IP A9009-0005

Бренд: Vitec Multimedia Страницы: 20

Бренд: ICP DAS USA Страницы: 8

Бренд: FXConnectX Страницы: 14

Бренд: Oshkosh Corporation Страницы: 92

I/O System 750 Series

Бренд: WAGO Страницы: 50

Greengate ControlKeeper 4

Бренд: Eaton Страницы: 24

Бренд: VIEWONHOME Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды