Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 116

background image

1

Publication 1769-UM005A-EN-P

Glossary

The following terms and abbreviations are used throughout this manual.
For definitions of terms not listed here refer to

Allen-Bradley’s Industrial

Automation Glossary

, Publication AG-7.1

.

A/D Converter

– Refers to the analog to digital converter inherent to the

module. The converter produces a digital value whose magnitude is
proportional to the magnitude of an analog input signal.

attenuation

– The reduction in the magnitude of a signal as it passes

through a system.

bus connector

– A 16-pin male and female connector that provides

electrical interconnection between the modules.

channel

– Refers to input interfaces available on the module’s terminal

block. Each channel is configured for connection to a thermocouple or
millivolt input device, and has its own data and diagnostic status words.

channel update time

– The time required for the module to sample and

convert the input signals of one enabled input channel and update the
channel data word.

common mode rejection

– For analog inputs, the maximum level to

which a common mode input voltage appears in the numerical value read
by the processor, expressed in dB.

common mode rejection ratio (CMMR)

– The ratio of a device’s

differential voltage gain to common mode voltage gain. Expressed in dB,
CMRR is a comparative measure of a device’s ability to reject interference
caused by a voltage common to its input terminals relative to ground.
CMRR=20 Log

10 (V1/V2)

common mode voltage

– The voltage difference between the negative

terminal and analog common during normal differential operation.

common mode voltage range

– The largest voltage difference allowed

between either the positive or negative terminal and analog common
during normal differential operation.

configuration word

– Word containing the channel configuration

information needed by the module to configure and operate each
channel.

cut-off frequency

– The frequency at which the input signal is

attenuated 3 dB by a digital filter. Frequency components of the input
signal that are below the cut-off frequency are passed with under 3 dB of
attenuation for low-pass filters.

«
...
105
106
107
108
109
...
»

Содержание Compact 1769-IR6





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact 1769-IR6

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 112

Бренд: WAGO Страницы: 56

Бренд: TagMaster Страницы: 28

Бренд: V-Tec Страницы: 16

EZH2O LZWS-LRPBM28K

Бренд: Elkay Страницы: 4

Бренд: claber Страницы: 21

Бренд: Kenco Страницы: 15

Бренд: Fender Страницы: 51

HBW8AQ 1M Series

Бренд: Halsey Taylor Страницы: 4

HomeMatic HMW-IO-12-FM

Бренд: eQ-3 Страницы: 36

Nelson 5500 Rotor

Бренд: Hunter Страницы: 16

Бренд: ESP Страницы: 24

PCIe-784 R Series

Бренд: National Instruments Страницы: 14

Бренд: New lift Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды