Allen-Bradley 8720MC Скачать руководство пользователя страница 40

Страница: 40 / 128

Rockwell Automation Publication 8720MC-RM001K-EN-P - September 2018

Chapter 4

Connector Data and Feature Descriptions

Sequence Signal Terminal
Block

The following table provides information on each of the TB3 terminals.

Table 13 - Sequence Signal Terminal Block (TB3) Descriptions

Function

Signal

Description

Sequence Input Signals

Enter the supplemental contact signal (normally open contact) of the main magnetic contactor.

(1)

RST

The reset signal (+24 VDC) is used to reset faults. Close the reset signal as required.

(1)

PWR

Enter the RUN signal (+24 VDC).

(1)

Power for Sequence Signals

0 V of +24V DC power

24V

+24V DC power (rating: 24V DC/0.2 Amps)

Sequence Output Signals

COM

Common for IP and RDY signals.

This is a contact signal that is turned ON during instantaneous power loss (contact rating: 30V DC/ 50 mA).

RDY

This is a contact signal that is turned ON when the unit is ready for operation (contact rating: 30V DC/ 50 mA).

FR, FR

This is a contact signal that opens when the fault occurs (contact rating: 250V AC/1 Amp or 30V DC/ 1 Amp).

(1) Because the driving current of sequence input signals is ≤5 mA, use a contact with a minimum applicable load is ≤5 mA.

2.2K

24V

8720MC-RPS

2.2K

RST

24V

8720MC-RPS

2.2K

PWR

24V

8720MC-RPS

+VC

Load

24V

COM

0VC
IP

4.64K

8720MC-RPS

+VC

Load

24V

COM

0VC
IP

RDY

4.64K

8720MC-RPS

Содержание 8720MC

































































































































Результаты поиска

Содержание 8720MC

Отзывы:

Allen-Bradley 8720MC, Руководство пользователя, Страница: 40 / 128

Результаты поиска

Содержание 8720MC

Отзывы: