Allen-Bradley 8720MC Скачать руководство пользователя страница 14

Страница: 14 / 128

Rockwell Automation Publication 8720MC-RM001K-EN-P - September 2018

Chapter 1

8720MC-RPS Regenerative Power Supply Overview

Catalog Number Explanation

8720MC-RPS units can be in parallel configurations with up to three units,
however, the units must be of the same size (catalog number) and series.

Table 1 - 8720MC-RPS Unit Catalog Numbers

Table 2 - 8720MC-RPS Accessory Catalog Numbers

8720MC-RPS Cat. No.

Units

Input Voltage

Power Rating
(single unit)

Power Rating

(1)

(2 parallel units)

Power Rating

(1)

(3 parallel units)

8720MC-RPS
Accessory Options

8720MC-RPS065BM

Leader

324…506V AC rms
Three-phase

37 kW

75 kW

110 kW

Includes 8720MC-RPS065 unit only.

8720MC-RPS065BM-HV2

Includes 8720MC-RPS065 unit plus:
• 8720MC-HF-B2 harmonic filter
• 8720MC-VA-B varistor

8720MC-RPS065BS

Follower

N/A

8720MC-RPS190BM

Leader

324…506V AC rms
Three-phase

125 kW

250 kW

375 kW

Required accessories:
• 8720MC-EF190-VB line filter
• Two 8720MC-LR10-100B line reactors

8720MC-RPS190BS

Follower

N/A

(1) Leader and follower units in the same configuration must be of the same size and series. You cannot mix units of catalog number 8720MC-RPS065 with 8720MC-RPS190 and you cannot mix units of

series # with series B.

Accessory Cat. No.

Accessory

Use in Applications With

8720MC-EF190-VB

EMC line filter
(required for CE)

Includes:
• AC line filter
• Magnetic contactor
• Harmonic filter
• Varistor

8720MC-RPS190BM

8720MC-RFI80

EMC line filter
(required for CE)

8720MC-RPS065BM

8720MC-LR03-032B

Line reactor

8720MC-RPS065BM

8720MC-LR05-48B

8720MC-LR10-62B

8720MC-LR14-70B

8720MC-LR10-100B

(1)

(1) Order two 8720MC-LR10-100B line reactors and wire in parallel for 200 A rating when used with the 8720MC-RPS190BM units.

8720MC-RPS190BM

8720MC-HF-B2

Harmonic filter

8720MC-RPS065BM

8720MC-VA-B

Varistor

Содержание 8720MC

































































































































Результаты поиска

Содержание 8720MC

Отзывы:

Allen-Bradley 8720MC, Руководство пользователя, Страница: 14 / 128

Результаты поиска

Содержание 8720MC

Отзывы: