Allen-Bradley 5069-IA16 Скачать руководство пользователя | Manualshive

Страница: 39 / 296

background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

39

Digital Module Operation in a Control System

Chapter 1

Power a Remote Compact 5000 I/O System That Includes Compact 5000 I/O Safety Modules

describes requirements that apply when you connect MOD power and

SA power to a Compact 5000 I/O system with standard and safety modules.

Table 7 - Connect Power to a Compact 5000 I/O System with Standard and Safety Modules

Power
Type

Requirements

Example System

MOD
Power

• You must use an SELV/PELV-listed

power supply to provide MOD
power to the controller.

• The total continuous current draw

across the MOD power bus must
not be more than 10 A max at
18…24V DC.
We recommend that you calculate
the total MOD power bus current
draw as you install modules.

SA Power

• You must use an SELV/PELV-listed

power supply to provide SA power
to the adapter.

• You must use a 24V DC power

supply to provide SA power to the
adapter.

• The total continuous current draw

across an SA power bus must not
be more than 5 A max at
18…24V DC.

• If you install safety modules

to the

right of a field potential
distributor, you must use an SELV/
PELV-listed power supply to
provide SA power.

• You must isolate the following

groups of modules on

separate

SA Power buses:
– Safety and non-relay DC-type

standard modules

– Relay DC-type modules
– AC-type modules

• If you install AC-type modules, you

must install them to the right a
field potential distributor. The
120/240V AC power supply that
provides SA Power is not required
to be SELV/PELV-listed.

• If you install relay DC-type

standard modules, you must
install them to the right of a field
potential distributor. The 24V DC
power supply that provides SA
Power is not required to be
SELV/PELV-listed.

5069-IB8S

5069-OBV8S

OUTPUT

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

Compact 5000™ I/O

MOD Power

SELV/PELV-listed

Power Supply

24V DC

+

-

5069-FPD

FIELD POWER

DC INPUT

5069-IB16

5069-IB8S

5069-OBV8S

OUTPUT

5069-FPD

FIELD POWER

5069-IB8S

5069-OBV8S

OUTPUT

Compact 5000™ I/O

SA Power

SA Power

24V DC

+

-

120/240V

AC

+

-

SA Power

24V DC

+

-

SELV/PELV-listed

Power Supply

SELV/PELV-listed

Power Supply

Compact 5000 I/O safety
modules and 24V DC
standard input module

Compact 5000 I/O
120/240V AC
standard modules

Compact 5000 I/O
safety modules

Non SELV/PELV-listed Power Supply

The modules on this SA power bus are 120/240V AC modules.

Therefore, this must be a 120/240V AC power supply.

However, it can be a non SELV/PELV-listed power supply

because there are no safety modules on the SA Power bus.

The SA Power to adjacent SA Power electrical isolation that

the 5069-FPD field potential distributor provides has a rating

of 240V AC (continuous) reinforced insulation type.

«
...
37
38
39
40
41
...
»

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5069-IA16

Бренд: JBL Страницы: 24

Бренд: Taco Страницы: 56

Бренд: Challenger Lifts Страницы: 20

Бренд: Mobotix Страницы: 25

Бренд: Dhollandia Страницы: 82

Бренд: LSP inc. Страницы: 6

Бренд: R. Beck Maschinenbau Страницы: 34

Бренд: ICP DAS USA Страницы: 6

Бренд: eMoMo Страницы: 2

Бренд: CAME Страницы: 16

COMPLIFT LIGHT DUTY 1

Бренд: Jarvis Страницы: 2

ADAP-KOOL AK-SM 800

Бренд: Danfoss Страницы: 4

Бренд: Bouyer Страницы: 4

PureBallast 135 Compact USCG

Бренд: Alfa Laval Страницы: 412

Бренд: Keysight Страницы: 46

Бренд: WAGO Страницы: 48

Бренд: RCA Страницы: 14

Compact 2 Series

Бренд: DATAEAGLE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды