Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 296

Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 31

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

31

Digital Module Operation in a Control System

Chapter 1

To help prevent other owner-controllers from receiving potentially erroneous
data, use the following steps when changing the configuration of a module in a
multiple owner scenario while online.

1. For each owner-controller, inhibit the connection to the module either

in the software on the Connection tab or the message dialog box
warning you of the multiple owner condition.

2. Make the appropriate configuration data changes in the software.

For more information on how to use the Logix Designer application to
change the configuration, see the following:
– Standard modules - Chapter 6,

Configure a Standard Module on

– Safety modules - Chapter 7,

Configure and Replace Safety Modules

3. Repeat

for all owner-controllers, to make the exact

same changes in each.

4. Clear the Inhibit checkbox in each owner-controller configuration.

Construct a System

Before you use your Compact 5000 I/O digital modules, you must complete
tasks that are based on the way that you use the modules. That is, if the
modules are used locally, remotely or both locally and remotely.

Local I/O Modules

Complete the following:

1. Install a CompactLogix 5380, CompactLogix 5480, or

Compact GuardLogix 5380 controller.

2. Install the modules to the right of the controller.

3. Install the end cap on the last module in the local system.

5069-OBV8S

SIL2 CPU

5069-L3100ERMS2

Compact GuardLogix

5069-OBV8S

5069-IB8S

5069-IB8S

OUTPUT

OUTPUT

SA P

ow

er

MOD P

ow

er

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

ow

er

MOD P

ow

er

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

Safety Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

OK

RUN

FORCE

FAN 1

SD

FAN 2

Compact

Logix

5480

B1

A1

1

2

A2

5069-L46ERMW

CONTROLLER

UPS

MP

SA

R
B
F

R

B

F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

IMPORTANT

Remember, you must use a Compact GuardLogix 5380 controller if
the local Compact 5000 I/O digital modules includes safety
modules.

For more information on controller compatibility, see

Software Compatibility on page 18

.

IMPORTANT

The end cap in a CompactLogix 5380, CompactLogix 5480, or
Compact GuardLogix 5380 control system covers the exposed
interconnection on the last module on the DIN rail.

If you do not install an end cap on the last module on the DIN rail,
equipment damage or injury can occur.

«
...
29
30
31
32
33
...
»

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов