Allen-Bradley 5069-IA16 Скачать руководство пользователя

Страница: 216 / 296

216

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Appendix A

Troubleshoot Your Module

Figure 24

show the status indicators on the Compact 5000 I/O standard DC

output modules.

Figure 24 - Compact 5000 I/O Standard Output DC Modules Status Indicators

Table 52

describes the I/O status indicators on Compact 5000 I/O standard

DC output modules.

DC OUTPUT

5069-OB16

5069-OB16, 5069-OB16F, 5069-OB16K

IMPORTANT

: The 5069-OB16F and 5069-OB16K module status indicators

appear the same as the indicators are shown on the 5069-OB16 module.

5069-OB8

Output Channel 0 (O00)

Output Channel 1 (O01)

Output Channel 2 (O02)

Output Channel 3 (O03)

LAO-

LAO+

Output Channel 4 (O04)

Output Channel 5 (O05)
Output Channel 6 (O06)
Output Channel 7 (O07)

LA1-

LA1+

Module Status
Indicator

I/O Status
Indicators

Output Channel 0 (O00)

Output Channel 1 (O01)

Output Channel 2 (O02)

Output Channel 3 (O03)
Output Channel 4 (O04)

Output Channel 5 (O05)

Output Channel 6 (O06)

Output Channel 7 (O07)
Output Channel 8 (O08)

Output Channel 9 (O09)

Output Channel 10 (O10)
Output Channel 11 (O11)
Output Channel 12 (O12)

Output Channel 13 (O13)

Output Channel 14 (O14)

Output Channel 15 (O15)

LA+

LA-

Module Status
Indicator

I/O Status
Indicators

Table 52 - I/O Status Indicators - Compact 5000 I/O Standard DC Output Modules

Indicator State

Description

Recommended Action

Off

Output is Off, or no module power applied

None

Steady yellow

The output is On.

None

Flashing red

One of the following:
• A No Load or Short Circuit condition

exists.

• 5069-OB8 only - A Field Power Loss

condition exists.

One of the following:
• Locate and correct the no load or short

circuit condition.

• Locate and correct the cause of field

power loss condition.

Содержание 5069-IA16









































































































































































































































































































Результаты поиска

Содержание 5069-IA16

Отзывы:

Похожие инструкции для 5069-IA16

Бренды по названию

Популярные бренды

Allen-Bradley 5069-IA16, Руководство пользователя

Результаты поиска

Содержание 5069-IA16

Отзывы:

Похожие инструкции для 5069-IA16

Бренды по названию

Популярные бренды