Allen-Bradley 5069-IA16 Скачать руководство пользователя | Manualshive

Страница: 210 / 296

background image

210

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 7

Configure and Replace Safety Modules

Replacement with ‘Configured Always’ Enabled

When the ‘Configure Always’ feature is enabled, the controller automatically
checks for and connects to a replacement module that meets all of the
following requirements:

• The controller has configuration data for a compatible module at that

network address.

• The module is in out-of-box condition or has an SNN that matches the

configuration.

If the project is configured for ‘Configure Always’, follow the appropriate steps
to replace a Compact 5000 I/O safety module.

1. Remove the old I/O module and install the new module.

2. Right-click your I/O module and choose Properties.

3. Click the Safety tab.

4. Click Reset Ownership.

5. Click OK.

6. Follow your company-prescribed procedures to functionally test the

replaced I/O module and system and to authorize the system for use.

ATTENTION:

Enable the ‘Configure Always’ feature only if the entire CIP

Safety Control System is not being relied on to maintain SIL 3 behavior
during the replacement and functional testing of a module.

Do not place modules that are in the out-of-box condition on a CIP Safety
network when the Configure Always feature is enabled, except while following
this replacement procedure.

If

Then

the module is in out-of-box condition

go to

No action is needed for the controller to take
ownership of the module.

an SNN mismatch error occurs

go to the next step to reset the module to out-of-
box condition.

«
...
208
209
210
211
212
...
»

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5069-IA16

Бренд: 2N Страницы: 4

Бренд: M-E Страницы: 12

PROX-BOOSTER 2G

Бренд: Nedap Страницы: 25

Бренд: Rain Bird Страницы: 96

Бренд: Waterway Страницы: 8

Бренд: ASL INTERCOM Страницы: 11

PORTAGANTRY 11000

Бренд: REID LIFTING Страницы: 21

Бренд: Contec Страницы: 15

SUITCASE Singlefold Ramp

Бренд: EZ-ACCESS Страницы: 2

Data Acquisition Device E Series

Бренд: National Instruments Страницы: 264

MICROPUMP 668-400-2

Бренд: Idex Страницы: 33

Бренд: HEEVE Страницы: 16

Бренд: ICP DAS USA Страницы: 4

Бренд: Roule Страницы: 6

Бренд: Toro Страницы: 28

10034 - Sa Skyfi Cd Audio System

Бренд: Delphi Страницы: 19

PressureMAT PMAT2

Бренд: PendoTECH Страницы: 48

Бренд: Redback Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды