manualshive.com logo in svg

Allen-Bradley 1771-OWN, Руководство по установке, Страница: 5 / 8

Поделиться
Скачать
Allen-Bradley 1771-OWN Скачать руководство пользователя страница 5

  5

Selectable Contact Output Module Cat. No. 1771-OWN

Publication 17715.37 - October 1995

Connecting Wiring to the Module

You make connections to the module through the field wiring arm
cat. no. 1771-WN. The arm pivots on the I/O chassis to connect with
terminals on the front of the module and acts as a terminal strip. The
wiring arm allows the module to be removed from the chassis
without disconnecting wiring.

1. Make certain all power is removed from the module before

making wiring connections.

2. Swing the wiring arm up into position on the front of the module.

The locking tab on the module will secure it into place.

3. Make your connections to the field wiring arm as shown in the

connection diagram. (Use the label on the front of the wiring arm
to identify your wiring.)

!

ATTENTION:   The field wiring arm terminal
identification number is not the same as the number of
the bit which controls that output.

Connection Diagram for the 1771-OWN Module

Output 0

Output 2
Output 4

Output 6

Not used
Output 10

Output 12

Output 14

Output 16

Not used

Output 0

Output 2

Output 4

Output 6

Not used

Output 10

Output 12
Output 14

Output 16
Not used

Common 0

Output 1

Output 3

Output 5

Output 7
Common 1

Output 11

Output 13
Output 15

Output 17
Common 2

Output 1
Output 3
Output 5

Output 7

Common 3

Output 11
Output 13

Output 15

Output 17

Note: Contacts shown in N.O.

configuration for simplicity.

(Actual wiring runs in this direction.)

2

4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40

Note: Terminals on the left are

even numbered, and terminals

on the right are odd numbered.

10539I

Allen-Bradley Spares

Содержание 1771-OWN









Отзывы:

Нет отзывов