Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 138

Страница: 138 / 176

138

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Appendix A

Get Diagnostic Status from Modules by Using Explicit Messaging

Table 44 - 1732ES-IB12XOBV2

Input Data

Input Status

Assembly Instance

Safety

None

20C

(1)

(1) The default Assembly Instance.

Point Status - Muting

34C

Combined Status - Muting

32C

Safety - Readback

Point Status - Muting

35C

Point Status - Muting - Test Output

37C

Output Data

Assembly Instance

Safety

–

233

(1)

Test

Combined

3C4

None

Table 45 - 1732ES-IB12XOBV4

Input Data

Input Status

Assembly Instance

Safety

None

20C

(1)

(1) The default Assembly Instance.

Point Status - Muting

34C

Combined Status - Muting

32C

Safety - Readback

Point Status - Muting

35C

Point Status - Muting - Test Output

37C

Output Data

Assembly Instance

Safety

–

233

(1)

Test

Combined

3C4

None

Table 46 - 1732ES-IB16 Modules

Input Data

Input Status

Assembly Instance

Safety

None

205

Point Status - Muting

335

Point Status - Muting - Test Output

365

Combined Status - Muting

315

Point Status

225

(1)

(1) The default Assembly Instance.

Output Data

Assembly Instance

Test

–

(1)

None

Содержание 1732ES-IB12XOB4

















































































































































































Результаты поиска

Содержание 1732ES-IB12XOB4

Отзывы:

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 138 / 176

Результаты поиска

Содержание 1732ES-IB12XOB4

Отзывы: