Allen-Bradley 160-DN2 Скачать руководство пользователя страница 26

Страница: 26 / 116

Publication 0160-5.18 - June 2003

3-10

Installation and Wiring

Connecting the DeviceNet Drop
Line to the Module

To connect your module DeviceNet drop line:

Turn off the network power supply.

Make sure that the DeviceNet 10-pin Linear Plug is correctly
wired (see

Figure 3.9

Locate the DeviceNet connector on the bottom of the module.

Insert the plug into the DeviceNet connector.

Figure 3.10
Installing the Drop Line

Removing Communication Module
From a Drive

If you need to reconfigure the Communication Module DIP switches,
you must remove the Communication Module from the drive.

Remove the DeviceNet plug from the Communication Module.

Press in on the module’s latch and then push away and up.

Grasp the module and pull straight up. Avoid bending or twisting
the contact pins located underneath the center portion of the
module.

Figure 3.11
Removing the Communication Module

ATTENTION:

Do not wire the Communication

Module with the network power supply on. Wiring the
module with the network power supply on may short
your network or disrupt communication.

COMM

UL
T

READ

CONFORMANCE TESTED

1 2 3 4 5 6 7

8 9 10

T1 U

–

T2 V

Содержание 160-DN2




















































































































Результаты поиска

Содержание 160-DN2

Отзывы:

Allen-Bradley 160-DN2, Руководство пользователя, Страница: 26 / 116

Результаты поиска

Содержание 160-DN2

Отзывы: