background image

GR8A

 

U

SER 

G

UIDE

 

 

 

 

 

This product complies with the European Electromagnetic 
Compatibility directives 89/336/EEC & 92/31/EEC and the European 
Low Voltage Directives 73/23/EEC & 93/68/EEC. 

Any changes or modifications to the equipment not approved by Allen & Heath 
could void the compliance of the equipment and therefore the users authority to 
operate it. 

 

GR8A User Guide AP4298 Issue 2. 

Copyright © 2001 Allen & Heath Limited.  All rights reserved 

 

Manufactured in the United Kingdom by  

Allen & Heath Limited 
Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK 
 
http://www.allen-heath.com 

 

Limited One Year Warranty   

This product has been manufactured in the UK by ALLEN & HEATH and is 
warranted to be free from defects in materials or workmanship for a period of one 
year from the date of purchase by the original owner. 

To ensure a high level of performance and reliability for which this equipment has 
been designed and manufactured, read this User Guide before operating. 

In the event of a failure, notify and return the defective unit to ALLEN & HEATH or 
its authorised agent as soon as possible for repair under warranty subject to the 
following conditions 

Conditions Of Warranty   

The equipment has been installed and operated in accordance with the 
instructions in this User Guide 

The equipment has not been subject to misuse either intended or accidental, 
neglect, or alteration other than as described in the User Guide or Service 
Manual, or approved by ALLEN & HEATH. 

Any necessary adjustment, alteration or repair has been carried out by ALLEN & 
HEATH or its authorised agent. 

The defective unit is to be returned carriage prepaid to ALLEN & HEATH or its 
authorised agent with proof of purchase. 

Units returned should be packed to avoid transit damage. 

 

In certain territories the terms may vary.  Check with your ALLEN & HEATH agent 
for any additional warranty which may apply. 

Содержание GR8A












Отзывы: