ALLEN & HEATH ANALOGUE ZONE Series Скачать руководство пользователя страница 14

Страница: 14 / 24

GR4 User Guide

AP10223 Issue_2

6.5

Page Input

The Page input is a 2-pole connection on

Euroblock type connector and is typically

configured to the Normally Open contacts.

Pin assignments are screen printed above the

connector or alternatively use the below wiring

diagrams.

Refer to 4.2 Control Section

③

for location details

2-Wire Paging Switch

0 = COM

+ = N/O (or N/C)

2-wire switch example.

6.6

Remote Connection

There are two methods for connecting a

remote control to the GR4. Remote control is

enabled via the rear mount dip switches.

Digital Remote Connection

The RJ45 “ZONE REMOTE” port allows for the

connection of the Allen & Heath PL-14 remote

controllers. A maximum of two PL-14’s can be

connected in daisy-chain wiring with various

control options depending on installation

requirements (see PL-14 manual for additional

details regarding cable types and length).

Refer to 4.2 Control Section

⑤

for location details

Do not connect remote port to

anything other than the designated remote

controller.

Digital Remote (RJ45 to RJ45)

1 = White/Orange

2 = Orange

3 = White/Green

4 = Blue

5 = White/Blue

6 = Green

7 = White/Brown

8 = Brown

RJ45 Wiring Example using TIA/EIA 568B standard.

WARNING - THIS APPARATUS MUST BE EARTHED.

CAUTION - HOT SURFACE, AVOID CONTACT.

NO USER SERVICEABLE PARTS INSIDE

CAUTION

Made in the UK by ALLEN & HEATH

SERIAL No:

A DIVISION OF HARMAN INTERNATIONAL INDUSTRIES Ltd.

T 3.15A 20mm 220 - 240V~

T 5.0A 20mm 100 - 120V~

FUSE TYPE AC SUPPLY

47-63Hz

320VA MAX

300W MAX

AC MAINS IN ~

Содержание ANALOGUE ZONE Series

























Результаты поиска

Содержание ANALOGUE ZONE Series

Отзывы:

Похожие инструкции для ANALOGUE ZONE Series

Бренды по названию

Популярные бренды

ALLEN & HEATH ANALOGUE ZONE Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ANALOGUE ZONE Series

Отзывы:

Похожие инструкции для ANALOGUE ZONE Series

Бренды по названию

Популярные бренды