Allegion interflex IF-4076-0 Скачать руководство пользователя страница 3

1

General information

© 2021 Interflex Datensysteme GmbH

IF-4076-0 Access Manager

3

1 General information

1.1 Short description

The IF-4076-0 access manager in metal housing with an integrated
IF-4070 controller is used to accommodate up to 16 I/O controller
boards and serves as a link between the host system and a maximum
of 16 terminals (slaves) of the IF-7xx/IF-8xx series.

1.2 Scope of delivery

The package contains:

n

Housing with integrated IF-4070 controller, supporting plate for I/O controller boards and power

n

n

n

n

n

supply unit

 

Cable gland, M20 x 1

.

5

 

Strain relief plates with screw nuts

 

Split ferrite

 

Accessory bag with screws, screw anchors and a key for the bolt lock

95-10436 product Info

 

Check the completeness and condition of the goods upon receipt and report any damage caused
during transport immediately.

1.3 Target group

This document is solely intended for 

experts

 and 

people trained in electrical engineering

.

Only perform the actions described in this document if you belong to this target group. Interflex
Datensysteme GmbH is not liable for any damages caused by improper installation or initial
operation.

Содержание interflex IF-4076-0





























Отзывы: