17
Owner’s Manual
Operation
NOTE: THE PARTS LISTED ABOVE ARE HELPFUL FOR LOCATING THE
CONTROLS MENTIONED BELOW.
CAUTION: PRIOR TO FIRST USING THE GENERATOR, THE ENGINE MUST BE
FILLED WITH OIL OF A HIGH QUALITY SAE 10W-30 GRADE ENGINE OIL.
TO DO SO, UNSCREW AND REMOVE THE ENGINE’S OIL DIPSTICK LOCATED
AT THE BOTTOM OF THE ENGINE CRANKCASE. FILL THE ENGINE’S
CRANKCASE UNTIL THE OIL LEVEL IS LEVEL WITH THE UPPER MARKED
LINE ON THE DIPSTICK. THEN SCREW THE DIPSTICK BACK INTO
THE OIL FILL HOLE.
Before Starting the Generator
1. Check that the engine power switch is in its
Fuel tank capacity:25L(6.6 gallons)
Choke lever
Air Filter
Recoil Starter
Oil Plug
Handel
Control Panel
Fuel Tank
“OFF” position.
2. Before the first use, remove the fuel
tank cap and fill the fuel tank with unleaded
gasoline. When fueling, be sure that the
fuel strainer is in place. Replace the fuel
tank cap. Thereafter, check the engine’s
fuel gauge for the amount of unleaded
gasoline in the fuel tank. If necessary,
refill the fuel tank with unleaded gasoline;
the generator must be turned off and
cooled down before refilling the fuel tank.
Use gasoline with a pump octane rating of 90 or higher.
We recommend unleaded gasoling because it produces
fewer engine and spark plug deposits and extends
exhaust system life.
Never use stale or contaminated gasoline or oil/gasoline
mixture. Avoid getting dirt or water in the fuel tank.
6WLYH[PVU JVU[»K
:[HY[PUN
;\YU[OLLUNPULZ^P[JO[V[OL¸9<5¹WVZP[PVU
;OLLUNPULZ^P[JOLUHISLZHUKKPZHISLZ[OLPNUP[PVU
Z`Z[LT
:;67!;VZ[VW[OLLUNPUL
9<5!;VY\U[OLLUNPUL
;OLM\LS]HS]LPZSVJH[LK\UKLY[OLM\LS[HUR>OLU
[OL]HS]LSL]LYPZPU[OL65WVZP[PVUM\LSPZHSSV^LK
[VMSV^MYVT[OLM\LS[HUR[V[OLJHYI\YL[VY)LZ\Y
[VYL[\YU[OLM\LS]HS]LSL]LY[V[OL6--WVZP[PVUHM[LY
Z[VWWPUN[OLLUNPUL
;VZ[HY[HJVSKLUNPULTV]L[OLJOVRLSL]LY[V[OL
¸:[HY[¹WVZP[PVU;VYLZ[HY[H^HYTLUNPULSLH]L[OL
JOVRLSL]LYPU[OL¸9<5¹WVZP[PVU
;OLJOVRLSL]LYVWLUZHUKJSVZLZ[OLJOVRL]HS]LPU
[OLJHYI\YL[VY
;OL¸:[HY[¹WVZP[PVULUYPJOLZ[OLM\LSTP_[\YLMYVT
Z[HY[PUNHJVSKLUNPUL
;OL¸9<5¹WVZP[PVUWYV]PKLZ[OLJVYYLJ[M\LSTP_[\YL
MVYVWLYH[PVUHM[LYZ[HY[PUNHUKMVYYLZ[HY[PUNH^HYT
LUNPUL
> .LULYH[VY
:;67
9<5
*OVRL3L]LY
¸:[HY[WVZP[PVU¹
65
6--
6WLYH[PVU JVU[»K
:[HY[PUN
:[VWWPUN,UNPUL
6WLYH[L[OL9LJVPS:[HY[LY!
7\SS[OLZ[HY[LYNYPWSPNO[S`\U[PS`V\MLLSYLZPZ[HUJL
[OLUW\SSIYPZRS`9L[\YU[OLZ[HY[LYNYPWNLU[S`
7\SSPUN[OLZ[HY[LYNYPWVWLYH[LZ[OLYLJVPSZ[HY[LY[V
JYHUR[OLLUNPUL
0M[OLJOVRLOHZILLUTV]LK[V[OL¸:[HY[¹
WVZP[PVU[VZ[HY[[OLLUNPULNYHK\HSS`TV]LP[[V[OL
¸9\U¹WVZP[PVUHZ[OLLUNPUL^HYTZ\W
;\YU[OLLUNPULZ^P[JO[V[OL¸:[VW¹WVZP[PVU
;\YU[OLM\LS]HS]LSL]LY[V[OL6--WVZP[PVU
>OLU[OLLUNPULPZUV[PU\ZLSLH]L[OLM\LS]HS]LPU
[OL6--WVZP[PVU[VWYL]LU[JHYI\YL[VYMSVVKPUNHUK[V
YLK\JL[OLWVZZPIPSP[`VMM\LSSLHRHNL
:;67
6^ULY»Z 4HU\HS
:[HY[LY.YPW
¸9\U¹7VZP[PVU
65
6--
20
Operation (cont’d)
Powering 120 Volt AC Tools And Equipment:
1
. Prior to powering tools and equipment, make sure the generator’s rated voltage, and amperage
capacity (
1
20 V AC @
41
.
7
AMPs) is adequate to supply all electrical loads that the unit will
power. If powering exceeds the generator’s capacity, it may be necessary to group one or more
of the tools and/or equipment for connection to a separate generator.
CAUTION: ATTEMPTING TO POWER SENSITIVE ELECTRONIC EQUIPMENT
WITHOUT THE USE OF AN APPROVED LINE CONDITIONER MAY CAUSE
DAMAGE TO THE EQUIPMENT. ALL-POWER IS NOT RESPONSIBLE FOR
ANY DIRECT OR INDIRECT DAMAGE CAUSED BY FAILURE TO USE AN
APPROVED LINE CONDITIONER.
2. Once the generator is running, simply connect the power cords of
1
20 volt AC powered
tools and equipment into the
1
20 volt AC dual outlets.
NOTE:THEGENERATORFEATURESAN AC NON-FUSETHERMAL PROTECTOR
TOPROTECTTHE AC CIRCUITIN CASEOFAN OVERLOAD.SHOULD
AN OVERLOADOCCUR,THEBREAKERWILL POP.
3.Disconnect all electrical powered tools and equipment from the generator’s
1
20 volt AC
duel outlets.
4
.After the engine and generator have completely cooled, store generator in a safe,clean,dry
location (if not already installed).
6000W Generator
