ALL POWER AMERICA PW3200, Руководство пользователя

Страница: 12 / 24

12 | ALL POWER™ PW3200 PRESSURE WASHER www.allpoweramerica.com
This pressure washer is intended for use only
with liquid car wash detergents, developed
specifically for pressure washers and with mild
soaps. Only use chemicals compatible with
the aluminum and brass parts. Powdered
soaps may clog the injection system. Always
use chemicals according to the manufacturers
directions. We assume no responsibility
for any damages caused by chemicals injected
through this pressure washer.
1. Attach injection tube assembly to the
detergent connection on the pump.
2. Open a container of chemicals and place
next to the unit near the injection tube.
3. Visually inspect strainer at the end of
the injection tube to verify that it is not
clogged
4. Insert the injection tube into the container
all the way to the bottom.
5. Remove the high pressure nozzle from the
wand and install the black injection nozzle.
The solution will automatically mix with the
water and discharge through the nozzle.
NOTE: For certain models, if the
engine throttle is not in the fast
position, the injection of the solution
may be decreased or stopped.
10
Owner’s Manual
This pressure washer is intended for use only with liquid car wash detergents, developed
specifically for pressure washers and with mild soaps. Only use chemicals compatible with
the aluminum and brass parts. Powdered soaps may clog the injection system. Always
use chemicals according to the manufacturers directions. We assume no responsiblity
for any damages caused by chemicals injected through this pressure washer.
1. Attach injection tube assembly to the detergent connection on the pump.
2. Open a container of chemicals and place next to the unit near the injection tube.
3. Visually inspect strainer at the end of the injection tube to verify that it is not clogged
4. Insert the injection tube into the container all the way to the bottom.
5. Remove the high pressure nozzle from the wand and install the black injection nozzle.
The solution will automatically mix with the water and discharge through the nozzle.
NOTE: For certain models, if the engine throttle is not in the fast position, the injection
of the solution may be decreased or stopped.
CLEANING TECHNIQUES
When cleaning with the pressure washer, many cleaning tasks can be solved with water
alone, but for most tasks, it is advantageous to use a detergent. A detergeng ensures a
quick soaking of the dirt allowing the high pressure water to penetrate and remove the
dirt more effectively.
APPLICATION OF SOAP OR DEGREASER
1. Apply the solution to the dry work surface. On a vertical surface, apply horizontally
from side to side starting from bottom to avoid streaking.
NOTE: Wetting the surface first is not recommended, it dilutes the detergent and
reduces its cleaning effects.
Please disconnect the Detergent Hose from the Pressure Washer when do not use
the soap or degreaser.
CAUTION
Detergent
Connection
Detergent
Hose
11
Owner’s Manual
Operation
Avoid working on hot surfaces or in direct sunlight to minimize the chances of the
chemical damaging painted surfaces. Damage may occur to painted surfaces if the
chemical is allowed to dry on the surface. Hold the nozzle far enough away from surface
to prevent damage to the surface.
2. Allow chemical to remain on the surface for a short time before rinsing.
3. Rinse with clean water under high pressure. On a vertical surface, first rinse from
the bottom up, then rinse from top down. Hold nozzle 6 to 8 inches from the work surface
at a 45° angle using the flat spray as a peeling tool rather than a scrub brush.
APPLICATION OF WAX
1. Immediately after cleaning, apply wax. Place injection tube in container of wax.
2. Apply the wax sparingly in an even layer. Apply to wet surfaces from bottom up for even
distribution and to avoid streaking.
3. Remove the suction tube from the wax bottle rinse off the surplus wax.
NOTE: If surplus wax is not removed, a hazy finish may result.
4. Wipe dry to reduce water spotting.
END OF OPERATION
When you have completed use of chemical injection system, remove tube from container.
Continue to run in low pressure position and inject clean water through the tube and
injection system by placing end of tube in a container of clean water. Continue to run
until it is thoroughly cleaned.
Maintenance
CONNECTIONS
Connection on pressure washer hoses, gun and spray wand should be cleaned
regularly and lubricated with the manufacturers recommended grease to prevent leakage
and damage to the O-ring.
NOZZLE
Clogging of the nozzle causes the pump pressure to be too high, cleaning is immediately
required.
A nozzle cleaner must only be used when the spray
wand is disconnected from the gun or personal injury
may occur.
1. Seperate the wand from the gun.
Fig 7
CLEANING TECHNIQUES
When cleaning with the pressure washer, many
cleaning tasks can be solved with water alone,
but for most tasks, it is advantageous to use
a detergent. A detergent ensures a quick
soaking of the dirt allowing the high pressure
water to penetrate and remove the
dirt more effectively.
Application of Soap Or Degreaser
1. Apply the solution to the dry work surface.
On a vertical surface, apply horizontally
from side to side starting from bottom to
avoid streaking.
NOTE: Wetting the surface first is not
recommended, it dilutes the detergent
and reduces its cleaning effects.
Please disconnect the Detergent Hose from
the Pressure Washer when not in use.
Avoid working on hot surfaces or in direct
sunlight to minimize the chances of the
chemical damaging painted surfaces.
Damage may occur to painted surfaces if the
chemical is allowed to dry on the surface.
Hold the nozzle far enough away from
surface to prevent damage to the surface.
2. Allow chemical to remain on the surface for
a short time before rinsing.
12 OPERATION | OWNER’S MANUAL