5
www.observint.com
© 2018, 2019 Observint Technologies. All rights reserved.
DNR
(Digital Noise Reduction): The DNR function can decrease the noise effect, especially when capturing
moving images in poor light conditions and delivering more accurate and sharp image. You can set the DNR
value from 1 to 9.
MIRROR
: OFF, H, V, and HV are selectable for mirror.
•
OFF
: The mirror function is disabled.
•
H
: The image flips 180° horizontally.
•
V
: The image flips 180° vertically.
•
HV
: The image flips 180° both horizontally and vertically.
FACTORY DEFAULT
Move the cursor to FACTORY DEFAULT and click Iris+ to reset all the settings to the factory default.
EXIT
Move the cursor to EXIT and click
Iris+
to exit the menu without saving.
SAVE &EXIT
To save your new settings, move the cursor to SAVE &EXIT and click OK (
Iris+
) to save the setting and exit
the menu.
Specifications
Camera
Image Sensor
5 MP CMOS image sensor
Effective Pixels
2560 (H) × 1944 (V)
Min. illumination
Color: 0.01 Lux @ (F1.2, AGC ON), 0 Lux with IR
Shutter Time
PAL
: 1/25 s to 1/50, 000 s
NTSC
: 1/30 s to 1/50, 000 s
Lens
Motorized VF lens: 2.7 ~ 13.5 mm
Horizontal Field of View
95.7° ~ 29.1°
Lens Mount
φ14
Day & Night
IR cut filter
Angle Adjustment
Pan: 0° ~ 360°; Tilt: 0° ~ 90°; Rotate: 0° ~ 360°
Synchronization
Internal Synchronization
Video Frame Rate
PAL
: 5MP @ 20 fps, 4MP @ 25 fps, 1080p @ 25 fps
NTSC
: 5MP @ 20 fps, 4MP @ 30 fps, 1080p @ 30 fps
Menu
AGC
Supported
D/N Mode
Auto/Color/BW (Black and White)
White Balance
ATW / MWB
BLC
Supported
Digital Wide Dynamic Range (DWDR)
Supported
Language
English. Chinese
Functions
Brightness, Sharpness, Digital noise reduction, Mirror, Smart IR
Interface
HD Video Output
1 Analog HD output
Button switch
Reserved for future use
General
Operating Conditions
-40°F
~
140°F (-40°C
~
60°C), Humidity 90% or less (non-condensing)
Power Supply
12 Vdc ± 15%, 24 Vac ± 15%
Power Consumption
8.9 W max.
Protection Level
IP67
Material
Metal, plastic
IR Range
Up to 135 ft (40 m)
Communication
Up the coax (HD-TVI output)
Dimensions
3.33” × 3.62” × 10” (84.5 mm × 92 mm × 255.1 mm)
Weight
1.55 lb (705 g) approx.
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
•
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
Troubleshooting
Problem
Possible Cause
Nothing appears on the screen
- Check the power connection.
- Check the video signal cable connection to the monitor.
- Check HD-TVI DVR camera settings to verify the video resolution mode of the
camera and HD-TVI DVR match
The video image is dim or not clear.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark.
- Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and
the surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor flickers
- Make sure that the camera isn’t facing direct sunlight or fluorescent light.
If necessary,change the camera position.