1
www.observint.com
ALI-TS1015VR_CQ
170707
What’s in the box
•
Camera assembly
•
Mounting hardware
•
Security L-wrench
•
This instruction guide
•
Drill template
Tools you need
To install the camera, you will need:
•
12 Vdc power source. See
Specifications
for requirements.
•
Tools and additional fasteners (may be required) for mounting the camera
•
Video and power extension cable
Installation
Before installation:
•
Make sure that the device is in good condition and all the assembly parts are included.
•
IR Reflection Prevention
: Avoid mounting the camera near reflective surfaces. The IR light from
the camera can reflect back into the lens. Do not remove the plastic cover until the cover is installation
is complete.
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
During installation:
•
Camera Lens
: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning
section.
•
Power supply
:
Camera drop cable
: The camera drop cable includes two connectors:
—
Video BNC connector
: For transmission of the HD-TVI video signal across a coax (75 Ω)
extension cable.
—
Power connector:
When applying Vdc power, observe the power polarity. See the drop cable
photo above for the connector polarity configuration.
Step 1. Mounting the camera
These cameras can be mounted on a wall or ceiling that has sufficient strength to support it. The video/
power drop cable from the camera can be routed either through mounting surface or through a cable guide
on the edge of the mounting base.
NOTE
This camera can be installed using a pendant mounting bracket with flange adapter or junction
box. Please refer to the instructions provided with those accessories for special considerations when
installing the camera with them.
1.
Using the mounting template to mark the holes for the camera mounting screws.
2.
Drill holes for the mounting screws into the mounting surface. The mounting screws and wall
inserts provided is appropriate for most surfaces. However, depending on the surface material and
strength, more appropriate fasteners may be required.
3.
Drill a 3/4” hole through the mounting surface for the drop cable, if necessary.
4.
If using wall inserts for the mounting screws, install the wall inserts at this time.
5.
Unscrew the three (3) dome assembly screws, and then separate the dome assembly from the
mounting base. The dome is tied to the base with a strap.
NOTE
: To keep the lens assembly clean,
do not remove the plastic protective packaging applied to the lens at this time.
ALI-TS1015VR 5MP HD-TVI
Vandalproof Dome Security Camera
Quick Installation Guide
The ALIBI ALI-TS1015VR dome camera include a new generation sensor with high sensitivity and advanced
circuit design technology. They feature high resolution, low image distortion and low noise features which
makes them suitable for surveillance and image processing systems. Features include:
•
5 Megapixel high-performance CMOS
•
HD-TVI HD output, up to 5 MP resolution
•
2.8 mm horizontal field of view: 81°
•
True Day/Night, DNR, Smart IR
•
Up-the-coax OSD menu
•
65 ft Full Frame SMART IR
•
IP67 weatherproof, IK10 vandalproof
•
Requires 5 MP HD-TVI compatible recorder (HD-TVI DVR)
•
Flange adaptor for pendant mounting (ALI-AF4) and junction box mounting (ALI-AJ4) are available
Mounting
base
Cable
guide
Dome
assembly
Dome
assembly
screw (3)
Lens
IR LED
Hole for
mounting
screw (3)
Product
label
Drop cable
Cable
guide
Camera mounting surface
Power
Connector
HD-TVI video
BNC connector
Camera drop cable connectors
