4
www.Observint.com
© 2016, 2017 Observint Technologies. All rights reserved.
Specifications
Video/Audio input
Video compression
H.264 / H.265 for IP camera
Video input
16-ch
BNC interface (1.0 Vp-p, 75 Ω), supporting coaxitron connection
Supported HD-TVI input
1080p/25Hz, 1080p/30 Hz, 720p/25 Hz, 720p/30 Hz, 720P/50 Hz, 720p/60 Hz, 3MP
Supported AHD input
720p/25Hz, 720p/30Hz
CVBS input
Support
IP video input
18-ch
Up to 8.0 MP resolution
Audio compression
G.711u
Audio input
4-ch, RCA (2.0 Vp-p, 1 KΩ)
Video/Audio output
CVBS output
Support
HDMI/VGA output
HDMI 1/VGA
: 1-ch, 1920 × 1080/60 Hz, 1280 × 1024/60 Hz, 1280 × 720/60 Hz, 1024 × 768/60 Hz
HDMI 2
: 1-ch, 4K (3840 × 2160)/30 Hz, 2K (2560 × 1440)/60 Hz, 1920 × 1080/60 Hz,
1280 × 1024/60 Hz, 1280 × 720/60 Hz, 1024 × 768/60 Hz
Encoding resolution
3MP (non-real-time); 1080P / 720P / 960H / 4CIF / VGA / CIF (real-time)
Frame rate
Main stream
: 25 fps (P) / 30 fps (N)
Sub-stream
: 960H / 4CIF / 2CIF (non-real-time); CIF (real time)
Video bit rate
32 Kbps to 10 Mbps
Audio output
2-ch, RCA (Linear, 1 KΩ) for CVBS, VGA
Audio bit rate
64 Kbps
Dual-stream
Support
Stream type
Video, Video & Audio
Synchronous playback
16-ch
Network management
Remote connections
128
Network protocols
TCP/IP, PPPoE, DHCP, Hik Cloud P2P, DNS, DDNS, NTP, SADP, NFS, iSCSI, UPnP™, HTTPS, ONVIF
Hard disk
SATA
4 SATA interfaces (4 HDDs max)
eSATA
Support
Capacity
Up to 6TB capacity per HDD.
External interface
Two-way audio input
1-ch, RCA (2.0 Vp-p, 1 KΩ) (independent)
Network interface
2, RJ45 10M/100M/1000M self-adaptive Ethernet interfaces
USB interface
2 USB 2.0 on the front panel 1 USB 3.0 on the rear panel
Serial interface
1 RS-232 serial interface 1 RS-485 serial interface, full-duplex 1 RS-485 keyboard interface
Alarm in/out
16 / 4
General
Power supply
100 to 240 Vac
Consumption (without
HDD)
≤ 65 W
Working temperature
14 ºF to 131 ºF (-10 ºC to +55 ºC)
Working humidity
10% to 90%
Dimensions (W × D × H)
17.5 × 15.4 × 2.8 inch (445 × 390 × 70 mm)
Weight (without HDD)
≤ 11.0 lb (5 kg)
to record data. Select (check the box for) that HDD, then click
Init
to initialize the disk.
NOTE
:
Init
will erase all data from the disk and
can take several minutes to complete. When the initialization is complete, click
Next
to continue.
•
Network Settings
: By default, the recorder acquires it’s network settings using DHCP (dynamic network settings). Depending on the
configuration of the network, these settings may change. To improve remote access to the recorder, Observint recommends that you
configure the DVR with fixed network settings. To easily change the DHCP acquired network settings to fixed network settings,
un-check the
Enable DHCP
option in the network setup menu, and then click
Apply
.
Step 8. Access the Menu system
After the initial setup of your QVR using the Wizard, the Menus interface enables you to refine your configuration settings and expand the
functionality of the system. To use most menus, the user must log into the NVR system, either locally or remotely, with administrative
privileges. To open the Menu system from the Live View screen, right click anywhere in the screen, then select
Menu
.
If ID Authentication is not disabled (see the
Menu | Configuration | General
settings), a login window will open. In the Login window,
select a User Name with administrative privileges, enter its password, then click
OK
. A window of Menu icons will open.
For additional information about using your system, refer to the
ALIBI Embedded Network Video Recorder Firmware V3.4.x User
Manual
provided electronically with your system.