1
www.observint.com
ALI-NZ60xx_CQ
170720
First install the install the ALI-NZ60 base station, install the add-on camera, and then configure the system.
Install your
Add-on camera
Install the
ALI-NZ60 Base Station
(pg. 1)
Configure the System
(pg. 5)
Install the ALI-NZ60 Base Station
pg. 1
ALI-NZ6012M Add-on Camera Installation
pg. 2
ALI-NZ6022M Add-on Camera Installation
pg. 3
ALI-NZ6032M Add-on Camera Installation
pg. 3
ALI-NZ6042HS Add-on Camera Installation
pg. 4
Configure the System
pg. 5
Specifications
pg. 5
Install the ALI-NZ60 Base Station
The ALI-NZ60 module can be anchored to a surface or set on a table or shelf. Ensure that it is positioned
where it can be reached by the cable attached to the camera head. The module should be installed in a
clean, low-dust location that is within the temperature and humidity specifications of the device. See the
Specifications
section at the end of this document.
ALI-NZ60 Base Station includes the following:
•
ALI-NZ60 Base Station module
•
Base Station mounting bracket
•
Rail bracket
•
Mounting hardware
Base Station
Mounting
Bracket
Mounting
hardware
Rail bracket
ALI-NZ60 Base Station front panel: LAN / power / alarm connections
RESET
button: To reset the device to the factory default settings, press and hold in the button while you
power on the base station for 10 seconds.
ALI-NZ60 Base Station back panel: camera / audio drop cable connectors , microSD card slot
To install the base station:
1.
Anchor the module on a surface:
ALI-NZ60 Series Camera System
Quick Installation Guide
This guide provides installation instructions for the following products:
Product SKU
Name
Camera Type
ALI-NZ60
Base Station for ALI-NZ60 Series Mini IP Security
Cameras
--
ALI-NZ6012M
Add-on 2.1 Megapixel 1080p WDR Pinhole Tube
Mini IP Security Camera
1080P WDR 3.7 mm Pinhole Tube Camera
ALI-NZ6022M
Add-on 2.1 Megapixel 1080p WDR Right Angle
Pinhole Mini IP Security Camera
1080P WDR 3.7 mm Right Angle Pinhole Camera
ALI-NZ6032M
Add-on 2.1 Megapixel 1080p WDR Wide Angle
Tube Mini IP Security Camera
1080P WDR 2.8 mm Wide Angle Tube Camera
ALI-NZ6042HS
Add-on IP Height Strip Camera
1080P WDR 3.7 mm Right Angle Pinhole Camera
The ALI-NZ60 series camera system features:
•
1/2.7” Progressive Scan CMOS
•
Up to 1920 x 1080 @ 30 fps for real-time output
•
IR cut filter with auto switch
•
Rotate mode, BLC, Defog and 120 dB WDR are supported
•
12 Vdc power supply or PoE supported
•
Built-in micro SD / SDHC / SDXC card slot, up to 128GB capacity (card not included)
•
Support for HLC, Defog
Status LEDs
ALI-NZ60 Base Station
Back panel
Right Angle
Pinhole Camera Assembly
ALI-NZ60 Base Station module with Right Angle Pinhole Camera
Pinhole Tube Camera head (left, cable not shown) and Wide Angle Tube Camera (right)
For more information
, refer to these documents available from your product vendor:
•
ALIBI™ Tools Utility Installation and User Manual
•
ALIBI™ IP Camera Firmware Version 5.3
(or later)
User Manual
To install the ALI-NZ60 camera system:
Brackets and hardware is provided to mount the camera assembly flat on a surface, on a surface using the
tilt-mount bracket, or behind a surface (concealed) with camera visibility through a peep hole. The
ALI-NZ60 Base Station module can be secured to a surface, or supported by a hanger (hanger not
provided).
•
Make sure the device in the package is in good condition and all the assembly parts are included.
•
Check the products specification for the installation environment.
•
If the product does not function properly, please contact your provider. Do not disassemble the
camera for repair or maintenance by yourself.
•
Make sure that the mounting surface is strong enough to support at least three times the weight of
the camera or base station.
