9
www.observint.com
© 2020 Observint Technologies. All rights reserved.
Alarm Trigger
Motion detection, tampering alarm, network disconnected, IP address conflict, illegal
login, HDD full, HDD error
Protocols
TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP,
SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, UDP, Bonjour
General Function
One-key reset, anti-flicker, three streams, heartbeat, mirror, password protection,
privacy mask, watermark, IP address filter
API
ONVIF (PROFILE S, PROFILE G), ISAPI
Simultaneous Live View
Up to 6 channels
User/Host
Up to 32 users 3 levels: Administrator, Operator and User
Client
Alibi Central Management Software (ACMS) V3.2 or later
Web Browser
Plug-in required live view: Microsoft Internet Explorer 8+,
Plug-in free live view: Chrome 45.0+, Firefox 52.0+
Interface
Communication Interface
1 RJ45 10M/100M self-adaptive Ethernet port
On-board Storage
Built-in micro SD/SDHC/SDXC slot, up to 128 GB
Reset Button
Yes
SVC
H.265 encoding and H.264 encoding support
Smart Feature Set
Behavior Analysis
Line crossing detection, intrusion detection, unattended baggage detection, object
removal detection
Exception Detection
Scene change detection
Face Detection
Yes
General
Operating Conditions
-22 °F ~ +140 °F (-30 °C ~ +60 °C), humidity 95% or less (non-condensing)
Power Supply
12 Vdc ± 25%, 5.5 mm coaxial power plug PoE (802.3af, class 3)
Power Consumption
12 Vdc, 0.5 A, max: 6 W PoE: (802.3af, 36 VDC to 57 VDC), 0.3 A to 0.2 A, max: 7.5 W
IR Range
120 ft (up to 30 m)
Wavelength
850 nm
Protection Level
IP67
Material
Camera body: Metal
Dimensions
Camera: Φ 5.4” × 4.9” (138.3 × 125 mm)
Weight
Camera: 1.6 lb. (725 g), with package: 2.1 lb. (966 g)
Using the Waterproof Ethernet Fitting
Install the
Waterproof Ethernet Fitting
on the Ethernet cable end at the camera when moisture
or contamination exists in the area near the camera. The fitting includes several parts that must be
installed in a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
Place the Lock Nut onto the network cable from the router
or switch as shown in the drawing to the right. The inside
threads must be toward the camera end.
3.
Place the rubber basket onto the network cable above the lock
nut as shown.
4.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the router
or switch.
5.
Install an RJ-45 connector onto the network cable.
6.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
7.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
8.
Push the rubber gasket fully into the end of the network cable
end cap.
9.
Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop cable
from camera
Network cable from
router or switch
Ethernet Fitting installed
Ethernet Fitting assembled and connected
Drop cable
end cap
Network drop
cable from
camera
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network
cable
from
router or
switch
Lock nut
