background image

1

www.observint.com

ALI-CS1080P_CQ 

12/17/14

Notes: 

• 

Lens

: The camera accommodates a standard C or CS mount lens. 

• 

Camera holder hole

: Provided on the upper side and underside of the camera housing. 

• 

Auto-iris interface

: DC driven (DD). Mode uses Damp+, damp-, drive+, drive- pins.  

4

2

3

1

Pin

Function

1

Damping -

2

D

3

Drive +

4

Drive +

 
Installation notes

Before installation: 

• 

Make sure that the device is in good condition and all the assembly parts are included.

• 

Check the specification of the products for the installation environment.

• 

Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.

• 

To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will 
provide the rated voltage and wattage for the camera. See the 

Specifications

 section.  

During installation: 

• 

Camera Lens

: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR 

array shield becomes soiled, clean it only with approved products. See the 

Cleaning

 section. 

• 

Monitor impedance

: Set the monitor impedance switch to 75 Ω.

• 

Power connector: 

The camera can be powered by 12 Vdc or 24 Vac. When applying 12 Vdc power, 

observe the power polarity. The polarity is marked on the back panel.  

Step 1.  Install the camera mounting bracket

The camera can be attached to a mounting bracket on the upper side or the underside of the camera. 
Follow the manufacturer’s instructions to attach the camera mounting bracket to the mounting surface.  

Step 2.  Attach the lens

The camera will accommodate a video-drive or DC-drive C- or CS-type lens. To attach the lens, do the 
following: 
1. 

Remove the lens protective cap from the lens mounting ring. 

NOTE

• 

Use care to prevent dust from contaminating the area between the lens mount and the lens. 
Install the lens assembly in a clean environment. 

• 

The weight of the lens must be less than 2.2 lbs (1 kg). 

2. 

If you are installing a C-type lens assembly, attach the C adaptor provided to the lens mounting ring 
on the camera body. 

3. 

Carefully screw the lens assembly clockwise onto the lens mounting ring (or adapter for C-type 
lenses) until it is fully seated. Tighten until snug. 

Auto-iris drive interface plug

Lens assembly

ALI-CS1080P HD-TVI Box Camera  

Quick Installation and User Guide

The ALIBI HD-TVI 1080P resolution C-mount box security camera provides high-resolution video over RG59 
coax or any standard analog CCTV cabling in diverse and challenging lighting conditions. A unique defog 
setting improves the camera’s visibility in rainy and foggy weather conditions.

• 

High performance CMOS imager for high definition video 

• 

Low illumination 0.01 lux @ (F1.2,AGC ON), 0 lux with IR

• 

ICR infrared filter auto switch

• 

OSD menu controlling, enable user to configure the detailed parameters

• 

3D NR noise reduction 

• 

Wide Dynamic Range (WDR) function

• 

Defogging function 

• 

Auto white balance, auto gain control

• 

Support coaxial camera controller 

Auto-iris drive interface plug

Lens assembly

Holes for mounting screws on top and underside

ALI-CS1080P camera (lens assembly not included) 

Power LED

RS-485 D+, D-

Alarm IN

Alarm OUT

Ground

D/N

Power input 

terminations for  

12 Vdc or 24 Vac

CVBS Video Out

HD-TVI 

 Video Out

Ground  

terminal

Joystick 

(for OSD)

Camera back panel connectors

What’s in the box

• 

Camera assembly

• 

This installation guide 

Tools you need

To install the camera, you will need:

• 

C- or CS-type lens

• 

12 Vdc or 24 Vac power source. See 

Specifications

 for wattage requirement. 

• 

Pedestal mounting bracket

• 

Video and power extension cables

• 

Tools and additional fasteners (may be required) for mounting the camera

• 

CCTV video setup monitor (optional) 

Отзывы: