2
www.observint.com
ALI-BC700VFG camera typical wall mounting
NOTE
If mounting the camera on a wall, ensure that the label on the mounting base, “
Bottom
,” is down.
If mounting the camera on a ceiling, orient the mounting base so that the cable guide is pointing
away from any source of water, dust, and other contaminates.
1.
Using the drill template provided, mark the location of the screws that anchor the mounting base
to the mounting surface. See the note above. If you are routing the drop cable through mounting
surface, also mark the position of the hole for the drop cable.
2.
Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface materials, more
appropriate fasteners may be required.
3.
Drill a 3/4” hole through the mounting surface for the drop cable, if necessary.
4.
Route the drop cable through the hole in the mounting surface, or through the cable guide in the
mounting base, then attach the camera assembly to the surface using the appropriate fasteners.
5.
Connect the camera drop cable to video and power extension cables as required.
6.
Connect the other end of the video extension cable to a video monitoring device, such as a CCTV
system monitor or DVR.
NOTE
Drop cable connectors are not waterproof.
7.
Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity
of the cable shown in the photo on page 1 of this guide.
Camera adjustments
1.
Apply power to the camera.
2.
Verify that video from the camera can be seen on the monitor.
3.
While observing video from the camera, loosen the mounting bracket pan, elevation and horizontal
line adjustment lock screws, point the camera at your surveillance target, and then tighten
adjustment lock screws or nuts to hold the camera in position.
For the ALI-BC700G camera
: The mounting bracket pan adjustment can be made after loosening
the lock nut (see the photo below). Use a Phillips #1 screwdriver for the elevation and horizontal line
adjustment lock screws.
0° ~ 90°
0° ~ 360°
0° ~ 360°
Use for horizon line
adjustment
Use for pan
adjustment
(lock nut)
Use for
elevation
adjustment
ALI-BC700G camera mounting bracket adjustment
For the ALI-BC700VFG camera
: Use Phillips #2 screwdriver for the pan, elevation and horizontal
line adjustment lock screws.
0° ~ 90°
0° ~ 360°
0° ~ 360°
Use for Horizon Line
Adjustment
Use for pan
Adjustment
Use for
Elevation
Adjustment
ALI-BC700VFG camera mounting bracket adjustment
4.
Adjust the sun shield (forward or back) to shield the lens from direct light, if necessary.
5.
If your camera has a varifocal lens (ALI-BC700VFG only), remove the cover on the underside of the
camera (slide the cover forward to remove) to access the focus and zoom adjustment screws. Use
the tool on the cover to adjust the zoom and focus if needed, and then reinstall the cover.
Focus
adjustment
Zoom
adjustment
Adjustment tool
Cover
ALI-BC700VFG camera Focus - Zoom adjustment
Specifications
Model
ALI-BC700G
ALI-BC700VFG
Image Sensor:
1/3” DIS
1/3” DIS
Signal System:
NTSC
NTSC
Effective Pixels:
976(H) × 496(V)
976(H) × 496(V)
Min. Illumination:
0.1 lux @ (F1.2, AGC on),
0 lux with IR
0.1 lux @ (F1.2, AGC ON),
0.14 lux @ (F1.4, AGC ON),
0 lux with IR
Shutter Time:
1/30 sec to 1/15,000 sec
1/60 sec to 1/100,000 sec
Lens:
3.6 mm
Angle of view: 68.4° (3.6 mm)
2.8 ~ 12 mm @ F1.4
Angle of view: 80° - 27.2°
Lens Mount:
M12
φ14
Adjustment Range:
Pan: 0 - 360°, Tilt: 0 -90°, Rotation: 0 - 360°
Pan: 0 - 360°, Tilt: 0 - 90°, Rotation: 0 - 360°
Day& Night:
IR cut filter with auto switch
IR cut filter with auto switch
Horizontal Resolution:
700 TVL
700 TVL
Synchronization:
Internal synchronization
Internal synchronization
Video Output:
1 Vp-p composite output (75 Ω/BNC)
1 Vp-p composite output (75 Ω/BNC)
S/N Ratio:
More than 62 dB
More than 62 dB
BLC:
On
On
Operating Conditions:
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity:
90% or less (non-condensing)
90% or less (non-condensing)
Power Supply:
12 Vdc ± 10%
12 Vdc ± 10%
Power Consumption:
Max. 1.8 W, (Max. 4 W with IR cut filter on)
Max. 4 W(Max. 5 W with IR cut filter on)
Weather Proof:
IP66
IP66
IR Range:
32 ~ 65 ft (10 ~ 20 m) approx.
98 ~ 131 ft (30 ~ 40 m) approx.
Dimension:
Φ2.76" × 5.89" (Φ70 × 149.5 mm)
Φ4.13" x 3.42" x 10.52"
(105 × 86.9 × 267.2 mm)
Weight:
0.79 lbs (360 g)
2.97 lbs (1350 g)
© 2014 Observint Technologies. All rights reserved.
