background image

6 of 19 

                                                   

 

2.0  Shipping Contents 

 
         The Jackbeam is fully assembled and packaged to protect it during shipping.   
          Included are the following components: 

o

  (1) Jackbeam Assembly, including: 

- Jackbeam 

Body 

-  Lifting Arms with Lifting Pads 
- Air/Hydraulic 

Pump 

o

  (4) Lifting Pad Extension Adapter 

-  (2) 3" Adapters 
-  (2) 6" Adapters   

o

  (1) Jackbeam accessory kit (2ft-1/4" polytube, 1/4" NPT elbows, Terminals, recoil  

     hoses, mounting brackets and hardware)  

o

  (1) Installation and Operation Manual 

o

  Wherever LOCTITE symbol is shown, apply LOCTITE #242 on required 

fasteners.  If fasteners are removed reapply LOCTITE before re-installing. 

 

3.0  Safety Instructions 

 

 

  Never allow unauthorized or untrained persons to operate the Jackbeam. 

 

  Thoroughly train all employees in the use and care of the Jackbeam. 

 

  Be aware of the clearance between the vehicle and the nearest overhead obstruction.  

 
 

 

  To avoid personal injury and/or property damage, the Jackbeam must only be operated by 

trained personnel. 
 

  Never overload the Jackbeam.  Capacity of Jackbeam is stated on nameplate, 

DO NOT

 

exceed. 
 

  Observe and avoid any pinch point areas of the Jackbeam. 

 

  Never operate a Jackbeam that is not in proper working order or in a manner not 

recommended by the vehicle or Jackbeam manufacturer. 
 

  Always ensure that the mechanical safety is engaged whenever a vehicle is supported by the 

Jackbeam. 
 

  Load evenly; do not place weight on one side of the Jackbeam. 

 
 
 

Содержание Snap-on Equipment EELR571A




















Отзывы: