background image

 

Wireless Timing Network WTN-DB 

 

 

 

 

-10- 

 

Updating of the WTN-DB 

To update a WTN-DB you need a WTN device. First you update the WTN as described 
in the WTN manual and then you can transmit the new firmware to the WTN-DB. The 
WTN-DB LED blinks red during the update. 
 

Transmit New Firmware to Other WTN Devices <RF-UPD> 

When  you have several WTN-devices in a network  you can make the update of the 
firmware on  one device through RS232 from a PC. This device can now update the 
firmware of all other devices in the same network. 

 

  Update the WTN as described in the WTN manual 

  Switch on all WTN-devices that you want to update from the WTN with the new 

firmware and check that they all use the same team. 

  Start the update as described below in the device with the updated firmware. For 

the devices that you want to update you do not have to make any further ad-
justment. 

  Go to the submenu <SETTINGS> by pressing continuously the key „MENU“ (1) 

for about 5 seconds.  

  Press „MENU“ (1) to move through the menu until it shows <RF-UPD>. 

  Press key „ON/OFF“ (2) to start the update. 

  Do not turn the WTN-WS off for two minutes after the update finished. Internal it 

will reprogram itself and if you turn it off it will destroy the software and the WTN-
WS is defect. 

 

 

Содержание WTN-DB













Отзывы: