manualshive.com logo in svg

Alfa Laval Toftejorg MultiJet 50, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval Toftejorg MultiJet 50 Скачать руководство пользователя страница 28

6 Maintenance

6.6

Stem Subassembly

Disassembly
1. Place machine in upright position.
2. Unscrew Gland (pos. 5). Note: Left-hand thread. Push out Main bush (pos. 6).
3. Turn machine upside down.
4. Remove Screws (pos. 10) in Gear wheel (pos. 8). To prevent rotation of Stem (pos. 3) mount two screws in two holes

opposite one another in BIG end of Stem. Place Stem in a vice held by the heads of the two screws..

5. Draw out Gear wheel with ball race (pos. 8) and Ball retainer with balls (pos. 27).
6. Push out Stem (pos. 3).

If Ball races in Body (pos. 28.3) and on Gearwheel (pos. 8.1) are extremely worn they should be replaced together with Ball
retainer with balls (pos. 27). How to replace Ball races see page 34.

If blue liners on Stem are extremely worn, they can be replaced. This part requires that a precise procedure is followed to
accomplish installation. It is highly recommended that an authorized Alfa Laval Tank Equipment Service Center perform the
replacement when necessary.

Reassembly
1. Push Stem (pos. 3) into Body. Turn machine upside-down.
2. Place Ball retainer with balls (pos. 27) and Gear wheel (pos. 8) into Body on Ball race. Rotate Gear wheel to check free

rotation.

3. Mount Gear wheel (pos. 8) with Screws (pos. 10) and tighten crosswise. To prevent rotation of Stem (pos. 3) mount two 1/4”

screws in two holes opposite one another in BIG end of Stem. Place Stem in a vice held by the heads of the two screws.

4. Turn machine to upright position. Remount Main bush (pos. 6) in Gland (pos. 5) and screw into Stem (pos. 3). Note:

Left-hand thread.

28

Содержание Toftejorg MultiJet 50

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды