Alfa Laval LKH-112 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 54

background image

3 Installation

The LKH-110 and -120P pump is highly efficient and econominal centrifugal pump, which meets the requirements of sanitary
and gently product treatment and chemical resistance. LKH-110 and the LKH-120P is avaliable in the following sizes, LKH-112,
-113, -114 and LKH122/P, -123/P, -124/P. The instruction manual is part of the delivery. Study the instructions carefully. The
large pump sizes are very heavy. ALfa Laval recommends the use of a lifting crane when handling the pump.

3.1

Unpacking/delivery

Step 1

!

Always use a lifting crane when handling the pump

CAUTION
Alfa Laval cannot be held responsible for incorrect unpacking.

WARNING:
Be aware that certain pump configurations can tilt, and thereby
cause injuries to feet or fingers. The pump should be supported
underneath the adaptor, when not installed in the process line.

Check the delivery for:
1. Complete pump.
2. Delivery note.
3. Instruction manual.
4. Motor instructions.
5. Test certificate, IF ORDERED!

Step 2
Remove possible packing materials from the inlet and the outlet.
Avoid damaging the inlet and the outlet.
Avoid damaging the connections for flushing liquid, if supplied.

* Remove packing materials!

3003-0085

!

*

*

*

Step 3
Inspect the pump for visible transport damages.

3003-0086

9

«
...
7
8
9
10
11
...
»

Содержание LKH-112























































Отзывы:

Нет отзывов

Похожие инструкции для LKH-112

Бренд: York Страницы: 27

Бренд: York Страницы: 32

Бренд: Zenit Страницы: 35

DynaFLO DOWB-S1 Series

Бренд: Camus Hydronics Страницы: 28

Omnivore XLSG200 Series

Бренд: Liberty Pumps Страницы: 12

Бренд: AMICUS Страницы: 12

Бренд: Sicce Страницы: 24

Бренд: CTC Union Страницы: 28

Бренд: salmson Страницы: 28

Бренд: Mannesmann Страницы: 3

HELIFLOW 8 Series

Бренд: Gardner Denver Страницы: 64

Lunaled Creative Set

Бренд: Oase Страницы: 48

JUNG PUMPEN JP09179/3

Бренд: Pentair Страницы: 42

Бренд: Robur Страницы: 82

Бренд: Sulzer Страницы: 4

Бренд: Fairland Pioneer Страницы: 36

Бренд: SAER Elettropompe Страницы: 44

Cylinder Passport

Бренд: WarmFlow Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды