background image

Item No. 1584-TMX/S

Installation & Operation

Since 1952

ALEXANDER ENGEL KG

Quality Model Kits & Accessories since 1952

P.O.Box 1133  D-75434 Knittlingen • Germany • Phone: int.+49-7043-93520  Fax: int.+49-7043-31548 • Email: [email protected]

Please read the following instructions and safety warnings carefully BEFORE you commence with
the assembly of this unit and installation of the dive system. For further safety instructions please
refer to the instructions supplied with Piston Tanks.

Only operate Piston Tanks when switch unit is completely connected. Otherwise
Piston Tanks will inevitably be damaged, resulting in total failure of the system.

During the charging period all batteries must be removed from the hull. 

NEVER

charge

batteries inside the hull as almost all battery types gas while being charged. Insufficient
air circulation during the charging period may lead to a serious 

EXPLOSION!

Engel Dive Systems have been primarily designed for use in Engel model submarines.
Therefore, we cannot guarantee satisfactory installation and/or operation in self-made
models or kits of other brands.

We are not liable for any personal injury or damage of any kind incurred during the assembly and/or
use of our products as we are neither able to delegate nor verify the assembly and/or use of these
items. Please adhere to your country’s safety guidelines during construction and operation of this
item. This product is not suitable for persons under 16 years of age. Technical specifications are
subject to change without notice.

Copyright ©2008 ALEXANDER ENGEL KG  1584-TMX_v11-08_E All rights reserved.

www.modelsubmarines.com

T

max

Proportional

Piston Tank Control

Version 2

with (optionally available)

Static Depth Controller

TAES

V2

Содержание 1584-TMX/S













Отзывы: